If the operator initially pushes the pedals at 20 rev/min and then initiates an angular acceleration of 6 rev/min2, determine the angular speed of the flywheel F (in rev/min) after the pedal has rotated 2 revolutions. Note that the pedal arm is connected to the chain plate A, which, when turning, drives the tethered pulley B through a coupling gear D. The belt wraps around the tethered pulley and then drives pulley E and the fixed flywheel. . B "A = 125 mm 20 mm "B = 175 mm "E = 30 mm

If the operator initially pushes the pedals at 20 rev/min and then initiates an angular acceleration of 6 rev/min2, determine the angular speed of the flywheel F (in rev/min) after the pedal has rotated 2 revolutions. Note that the pedal arm is connected to the chain plate A, which, when turning, drives the tethered pulley B through a coupling gear D. The belt wraps around the tethered pulley and then drives pulley E and the fixed flywheel. . B "A = 125 mm 20 mm "B = 175 mm "E = 30 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

determine the number of revolutions done by Disk E at the same time
Illustrate the force-inertia diagram Describe the relationship between the angular accelerations of gears A and B? Which of the following equations used to solve the problem is INCORRECT?
2- Cam Determine the acceleration of the shaft B for 0=60o if the crank OA has an angular acceleration 8 rad/s2 and an angular velocity 4 rad/s at this position. The spring maintains contact between the roller and the surface of the plunger. B A 80 mm -20 mm C
Determine the displacement of link 4 if the crank (link 2 )is rotated 135 degree clockwise.
The slider block has the motion shown. r=140mm, h=600mm What is the wheel's angular acceleration?
5-1. In the crank and rocker mechanism, AD = 2½ in.; AB = 1¼ in.; DC = 1% in.; BC = 2% in. Angle BAD = 60°. (1) Name the links of this four-bar linkage. (2) Move the link AB through an angle of 30° each side of its present position and find the corresponding positions of BC and DC. (3) If the angular speed of AB is 1 rad/sec, find the angular speed of DC and BC in the position shown. Consider 8° angle interval Machine elements lab subject
The thin rectangular block is supported at its corners by small rollers resting on smooth horizontal surfaces. If b=0.5 m and h= = 0.3 m, calculate the magnitude of the angular acceleration of the block at the moment when the supporting surface at B is suddenly removed. Present your answer in rad/sec² using 3 significant figures. AC B
A cyclist pedals constantly at 7.9587 rad/s the wheels are 336.5mm in radius. If the chain is directly connected with the sprockets which are 76 mm in radius (front sprocket) and 35mm in radius (rear sprockets), Determine the angular speed of the wheel in rad/s.
dynamic slender rods are fixed together as shown at left determine the anguler acceleration of the system when it is released.
(a) Find the final speed V of the center of mass of the wheel once the wheel starts moving.
The figure shows the internal gearing of a "spinner" used for drilling wells. With constant angular acceleration, the motor M rotates the shaft S to 100 rev/min in 1 = 2 s starting from rest. Determine the angular acceleration of the drill-pipe connection D and the number of revolutions it makes during the 2-s start up. 60 mm- 150 mm D
If the gear is turning at rads 2 and the rack (2 racks) is moving accelerating (6 ft / s) towards the busbar, answer the question Note: The wheel is always in contact without slip with the fixed path F. find acceleration of 3ft point A on gear 1.5ft