Answered: If the DC current gain of a certain…

If the DC current gain of a certain transistor operating in the linear region is 30 and the base current is 1 mA, the collector current is O a. 0.033 mA Ob 1 mA O c. 30 mA Od unknown

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A current-source bias circuit in the figure below has the following values: VDp = 10 V, Vee = -6 V, and Rg = 10,045,170 ohms. To produce a 13 mA drain current and a 7 V drain voltage, determine the value of Rp in ohms. Vpp Rp Rg RE -VEE
At high levels of gate current, the characteristics of an SCR approach those of what semiconductor device? a. MOSFET b. BJT c. JFET d. Diode
Choose whether the followings are True or False. 1. The MOSFET has 2 terminals Drain and Source. 2. An E-MOSFET operates in the depletion mode. 3. The LED emits light when reverse biased. 4. In the n-channel E-MOSFET, VGs(th) has a positive value. 5. A diode conducts current when forward biased and blocks current when reverse biased 6. An n-channel D-MOSFET with a positive Vcs is operating in the enhancement mode. 7. The varactor diode acts as a variable capacitor under forward bias conditions. 8. Once a BJT transistor is in the saturation, a further increase in base current will cause the collector current to increase. 9. In a given BJT transistor amplifier, Rc=2.2KQ and r'=20 Q then the voltage gain is equal to 110. 10. Voltage Amplification Av in a BJT is the output voltage divided by the input current
The operating point of the npn transistor is defined by a couple of values: lç and Ver. Select one: O True O False
For the JFET with maximum drain current 9mA, drain current 2.5mA at gate to source voltage 4V. Calculate the pinch off Voltage.
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
Determine the VDS and the drain current for the E-MOSFET circuit shown. The data sheet for this particular MOSFET gives ID(ON)=500 mA at VGS=10 V and VGS(th)=1 V.
TEST Read the question carefully. Write the letter for each correct answer in the blank space provided. A 1. Maximum power is delivered from a source of power to a load when the a. load current is equal to the power source current b. impedance of the load is equal to the output impedance of the power source c. output impedance of the power source is high compared to the impedance of the load d. output impedance of the power source is low compared to the impedance of the load 2. The emitter follower is a (an) a. impedance matching device b. high gain voltage amplifier c. phase inverter d. combination power and voltage amplifier 3. The emitter follower uses a. no collector resistor b. a forward bias collector-base junction c. negative feedback (degeneration) d. an NPN transistor only 4. The emitter follower has output resistance. a. high, high b. low, low c. low, high d. high, low input resistance and 5. The current gain of an emitter follower is a. less than 1 b. equal to 1 c. greater…
3. In a certain n-channel JFET, Ipss= 8 mA and Vp=-4 V. (a) Determine the value of Ves for maximum drain current. (b) Calculate the drain current for VGs=-5 V (c) Calculate the drain current for Ves=-2 V (d) Determine the maximum value of VGs for cut-off condition.
A common- configuration has the input at the base and the output iat the collector. base emitter collector
3V 2. In Figure 2 next, find the voltage at the collector assuming that the BJT is in active mode. After finding the voltage at the collector determine if the transistor is really in active mode or not. Use VBEaetive = 0.7V, and ß = 100. É IK $ IK Figure 2 3 IK -3V