If a polynomial function of degree 4 has 1+i as one of its roots, what is the maximum number of real roots can it have? 3 1 Differentiate f(x) = In (sin a).

Q: Actually, (a) and (b) were incorrect I already submitted it with a and b then I got the result…

A: Concurrent force system is a system of forces in which line of action of all the forces passes…

Q: Find the value of a. TO a. Vs +3

A:

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: A water tank consists of a cylinder section enclosed by hemispherical shell with the thickness of 15…

A:

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: Q1 A horizontal beam BC is subjected to uniformly distributed load, w and at the same time it is…

A: For solution refer below images.

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: 2 m Find the angle theta. a = 5. b = 3. 1m 1m D

A:

Q: Write the general equation of the circle of center (0, 4) and radius 4. Figure is not required.

A: The generalized equation of a circle with centre at origin and radius = r units is as given below:…

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: 1-23.Determine the length of side C of the triangle shown in Figure P1-23.

A:

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: The figure below has the following weight per length. W₁ = 150 lb/ft W₂ = 175 lb/ft W3 = 130 lb/ft…

A: given;   w1=150lb/ftw2=175lb/ftw3=130lb/ftAB=1ftBC=6ftCD=4ftDE=5ftEF=8ftlets take reaction force at…

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: y 4+B 5+C 2 3. 1.Find The size of the area number 1 (triangle) 2.Find The center of the numbered…

A: Given data: h1=3+Ab1=4+B Need to determine the centroid and area of the shape 1.

Q: 21 Given, z1=2+3j and z2=3-4j, determine the argument in two decimal places of the resulting value…

A: Given:z1=2+3jz2=3-4j

Q: E 12.5 m C А 8 m 5 m

A:

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55…

A:

Q: Q3: Draw the geometry shown in figure below . 88 38 12 719 -28 12 50

A:

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: Move the forces in the shape to point a

A:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: A steel collar has an inside diameter of 1-1/8 in., an outside diameter of 3-3/4 in., and a length…

A: Given: internal diameter Di = 1-1/8 = 9/8 inches outer diameter Do = 3-3/4 = 15/4 inches length =…

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm A 1 cm B 0.5 cm D 6 cm E 0.75 cm F 0.75 cm 0.75…

A: Solution:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.