I) Determining the voltage amplitude and angle values of each busbar II) To determine the active and reactive power values flowing from each transmission line III) To determine the active and reactive power loss values in each transmission line IV). Determining the total active and reactive power loss values in transmission lines in the power system V) To determine the power system temporary stability limit values To explain the reasons for load flow in power systems given above, which option is the correct one of the 5 explanations given? A) II,III,IV B) I,II C) I,II,III D) I,IV E) I,II,IV

I) Determining the voltage amplitude and angle values of each busbar II) To determine the active and reactive power values flowing from each transmission line III) To determine the active and reactive power loss values in each transmission line IV). Determining the total active and reactive power loss values in transmission lines in the power system V) To determine the power system temporary stability limit values To explain the reasons for load flow in power systems given above, which option is the correct one of the 5 explanations given? A) II,III,IV B) I,II C) I,II,III D) I,IV E) I,II,IV

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.60P: PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06...

See similar textbooks

Similar questions

With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Figure 3.39 shows a oneline diagram of a system in which the three-phase generator is rated 300 MVA, 20 kV with a subtransient reactance of 0.2 per unit and with its neutral grounded through a 0.4- reactor. The transmission line is 64km long with a cries reactance of 0.5-/km. The three-phase transformer T1 is rated 350MVA.230/20kV with a leakage reactance of 0.1 per unit. Transformer T2 is composed of three single-phase transformers, each rated 100 MVA, 127/13.2kV with a leakage reactance of 0.1 per unit. Two 13.2kV motors M1 and M2 with a subtransient reactance of 0.2 per unit for each motor represent the load. M1 has a rated input of 200 MVA with its neutral grounded through a 0.4- current-limiting reactor, M2 has a rated input of 100 MVA with its neutral not connected to ground. Neglect phase shifts associated with the transformers. Choose the generator rating as base in the generator circuit and draw the positive-sequence reactance diagram showing all reactances in per unit.
Transmission line conductance is usually neglected in power system studies. True False
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance diagram of the system. i. Construct the bus admittance matrix, Xeus and bus impedance matrix, Zous of the system. I. Evaluate the fault current, bus voltages and line current during the flow when a balanced three-phase fault occurs on bus 1. bus 1 bus 2 j65 N G G 25 MVA 25 MVA 13.8 kV 15% 13.2/69 kV 11% 25 MVA 69/13.2 kV 11% 15 MVA 13 kV 15% Figure 1(b) m
Fill in the blanks 1. Grounding is connecting …….. of electrical equipment to earth. 2. When a …………………………….… fault occurs on an ungrounded neutral system, the potential of the healthy phases rise to the line voltage. 3. The method of reactance grounding is not used because of ……………………… appearing under fault conditions. 4. The cosine of the angle between the ………………………………………. and the ………………………………...…… is called the sending end power factor. 5. The AC power delivered to a load is equal to ………........
2. What's the primary instrument for locating a break in a cable during emergency maintenance?A. OSAB. OTDRC. MultimeterD. Power meter
b) A fault occurs at bus 3 of the network shown in Figure Q4. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, transformer and load are given in Figure Q4. V₁ = 120° p.u. V₂ = 120° p.u. V₂ = 1/0° p.u. V₂= 120° p.u. jXj0.1 p.u. JX2) 0.1 p.u. jX0j0.15 p.u. jXn-j0.2 p.u. 1 JX(2)-j0.2 p.u. 2 jX)=j0.25 p.u. JX20-10.15 p.u. jXa(z)-j0.2 p.u. 4 jX2(0)=j0.2 p.u. jXT(1) j0.1 p.u. jXT(2)=j0.15 p.u. jXT(0)=j0.1 p.u. Figure Q4. Circuit for problem 4b). = jXj0.1 p.u. j0.1 p.u. - JX(2) JXL(0) 10.1 p.u. = (i) Assuming a balanced excitation, draw the positive, negative and zero sequence Thévenin equivalent circuits as seen from bus 3. (ii) Determine the positive sequence fault current for the case when a three- phase-to-ground fault occurs at bus 3 of the network. (iii) Determine the short-circuit fault current for the case when a one-phase- to-ground fault occurs at bus…
b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, and transformer are given in Figure Q3, where X and Y are the last two digits of your student number. V₁ = 120° p.u. V₂ = 120° p.u. jX(1) j0.1Y p.u. jX2)= j0.1Y p.u. jXko) j0.1X p.u. - 0 jX(1) = j0.2 p.u. 1JX(2) = 0.2 p.u. 2 jX1(0) = j0.25 p.u. jX2(1) j0.2 p.u. V₁=1/0° p.u. jX(2(2) = j0.2Y p.u. jX2(0) = j0.3X p.u. = V₂ = 120° p.u. jXT(1) j0.1X p.u. jXT(2) j0.1X p.u. JX3(1) j0.1Y p.u. JX3(2)=j0.1Y p.u. jXT(0) j0.1X p.u. JX3(0)=j0.15 p.u. 0- = 3 = Figure Q3. Circuit for problem 3b). For example, if your student number is c1700123, then: jXa(n) = j0.13 p. u., jXa(z) = j0.13 p. u., and jXa(o) = j0.12 p. u. 4 (i) Assuming a balanced excitation, draw the positive, negative and zero sequence Thévenin equivalent circuits as seen from bus 4. (ii)…
estion 9 The fault current level of a circuit breaker used in a transmission line with phase voltage 2.2 kV and breaking capacity 50 MVA is yet ......kA. vered -ked out of Flag question estion 10 The voltage between lines in a transmission line is the maximum value of the sine waveform. yet vered Select one: -ked out of O True Flag question O False
400Ω A k=0.9 600Ω B k=0.8 66Ω 600Ω