I need to find the reactions with the drawing

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A:

Q: design of CAM process

A: CAM- Computer Aided Manufacturing is the use of software and computer aided machinery in to control…

Q: the truss carries forces shown in the figure. determine the resultant of the forces and its…

A: Consider the figure,

Q: I beleive this is incomplete or I do not understand it at all

A:

Q: Calculate the stresses that will occur in the pipe for the water pipe buried 5 meters into the…

A: The stress is the dependent parameter and strain is an independent parameter and stress is defined…

Q: 3 cm 7 cm 5 cm 5 cM Detenmine the Folloeing %3D

A: Calculation of area and moment of inertia

Q: given truss. Pls, indicate the scale. 1000 lb 2000 lb 1000 lb 2000 lb 1000 lb D 1000 lb THE no 2000…

A: given the truss and applied load for the truss

Q: In detail, write about the introduction to 3D Shearing transformation.

A:

Q: 2) This table has three columns. First, match each set of Boundary Conditions (the left column) to…

A: Answer  Consider first Beam from middle column We get boundary condition for above beam θ0 = 0 and…

Q: How many centimeters long is side AC?

A:

Q: what is shear force at x= 8ft

A: Given Load 100 lb/ft and 300 lbSpan 12 ftReaction at A and D are 246.667 and 653.333 lbTo find out…

Q: Find the Ultimate Moment (Mu) of a Wide Flange Section with the following Properties: Web Flange…

A:

Q: What is the degree of kinematic indeterminacy of the truss as shown in figure?

A:

Q: Refer to the photo provided and please make sure your handwriting is readable. L1 = 2.02 m L2 = 1.21…

A:

Q: Refer to the photo provided and please make sure your handwriting is readable. Determine the ff: 1.…

A:

Q: 5 Find the centroid of the following structure. (20 2.5" dia hole- centered 4" 5" 3" 4" 6" 3"

A:

Q: Define the Stresses Along the Vertical Axis of Symmetry ?

A: Solution: Stresses that are acting on  normal face in a negative direction. Stresses are the forces…

Q: Problem Set 5.pd O File C/Users/naswe/Downloads/Problem%20Set%205.pdf ... O | D Page view A Read…

A:

Q: what is force in FG

A: Given data in question  Force 60 kips Span 16 m Height 15 m To find out  Member force in FG

Q: How did u calculate minor and major stress

A: Minor and major stress

Q: Draw shear force Diagram 600 lb 4000 lb ft |C D 10 ft + 5 ft 5 ft-

A: Support reaction : ∑MB=0RA×20-600×10+4000=0RA=100 lb∑FY=0RA+RB-600=0100 +RB-600=0RB=500 lb

Q: Problem 6 Identify the zero-force members in the following trusses, by observation only. Identify…

A: Given data in question  Structures  Loads To find out  Zero force members

Q: DETERMIME Fou つ こ I =

A:

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: Determine external indeterminacy

A: Given:- A frame is given with fixed support To determine:- The external indeterminacy

Q: There are support reactions Ay and By which both equal 3.5kN going upwards.

A:

Q: Describe the method of virtual forces applied to beams?

A: The method of virtual force is defined as the total external work by the unit load is equal to the…

Q: What is the rod reading at the arrow? 4 3 7 3 =6

A: Rod reading:- The number on the rod is parallel to the die-observing device's height. The elevation…

Q: 2. Determine the moment of area of the given structural built-up section composed of a 8"x1" top…

A: Moment of inertia The moment of inertia, also known as the angular mass or rotational inertia, is a…

Q: Estimate the reinforcing bar of a continuous beam supported by 3 columns (400 mm x 400 mm) spaced at…

A:

Q: Chapter 5, Section 5.2, Question 40 A 50-kN force acts at point D in the yz plane on the linkage.…

A: For calculating we have to find values of following Distance between B and D Component of forces on…

Q: Explain" T" beam action of a continuou

A: The T-beam, though simple in design, contains multiple design elements of interest. Unlike an…

Q: 24 14 14 2

A:

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Section 200 UB 29.8 The concentrated point load acting on the beam is 12 kN

Q: What is the difference between the bent frame structure and the rigid frame structure? Subject :

A: There are several frame structure types that may be employed for building construction. They may be…

Q: Q3. For the rectangular section shown below, calculate the moment of inertia for both x - x axis and…

A:

Q: For the 2d coordinate system below, complete the following: a) Break up the force vector into Fx and…

A: In order to obtain the components of a vector. Two dotted lines are projected as shown and the…

Q: truss of this object and summary

A: The given structure is a truss.

Q: [Question ID 785899] The figure below shows a simplified section of a box girder. The area of the…

A:

Q: Discuss rigid methods

A: Rigid method is used for designing mat foundation in which it is assumed that mat foundation is…

Q: Draw the figure in a half-meter cross-section paper, and provide a scale. -The solution will be…

A: Step 1:Step 2:(c) Shear Flow CalculationStep 3:Step 4:

Q: Sketch the following forces on the x, y, z coordinate axes. Show a, ß,y. Note: Scale: 1cm = 10 kN a.…

A: Here the orientation is shown with XY plane vertical

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.