Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)
10th Edition
ISBN: 9781337399128
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Related questions
Question
I have two ESP32 boards connected to an LED, an NRF24L01 module, and a Mini Pushbutton Switch. I want to name them Chris and David, and would like to implement bidirectional communication between the two of them. If Chris’ Mini Pushbutton Switch is pressed, the LED turns on and Chris says “Howdy” to David. If David’s Mini Pushbutton Switch is pressed, the LED turns on and David says “Great” to Chris. What are the Arduino IDE codes?
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 2 steps
Knowledge Booster
Similar questions
- I have two Arduino Uno Rev3 boards. One (named Alvin) is connected to an NRF24L01 module, two LEDs, and one Mini Pushbutton Switch. The other (named Brian) is connected to an NRF24L01 module, two LEDs, one DRV8833 DC/Stepper Motor Driver, and a 9V battery. I want to implement bidirectional communication between these two Arduino Uno Rev3 boards. Alvin must have its first LED on at all times unless the Mini Pushbutton Switch is pressed and unless Alvin receives a "Coming" message from Brian. If the Mini Pushbutton Switch is pressed, Alvin must send a "Hello" message to Brian. Brian must have its first LED on at all times. Brian's DRV8833 DC/Stepper Motor Driver must move at a PWM speed of 80. Unless Brian receives a "Hello" message from Alvin, Brian's DRV8833 DC/Stepper Motor Driver must take a 3-second pause every 12 seconds. 2 seconds before the DRV8833 DC/Stepper Motor Driver's 3-second pause, Brian must send a "Coming" message to Alvin. When that happens, Alvin must have its second…arrow_forwardI have four ESP-WROOM-32D boards, and four NRF24L01 modules. Each ESP-WROOM-32D board is connected to one NRF24L01 module. I want one NRF24L01 module to send a "Hello" message to the other three NRF24L01 modules at the same time. What is a good starter code in Arduino IDE?arrow_forward1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2,…arrow_forward
- Draw the wiring diagram of DELTA DVP-SS2 | plcarrow_forwardQuestion 9arrow_forwardQ4 Table Q4 shows the mode and task that need to be implemented using PIC18F452. (a) Mode Switch (SW1) 1 Press 1 time 2 Press 2 times Table Q4 Task Move the LED right to left and continue back from left to right. Control the duty cycle of PWM for the period of 2 ms. You are given 1 switch, 1 potentiometer and 8 LEDs, sketch the interface between the components and PIC microcontroller. (b) Construct a C18 program to control the tasks in Table Q4. (4 marks)arrow_forward
- Question 8arrow_forwardDraw a diagram and label the parts: PIC16F1829 interface potentiometer. % of rotation display on LCD.arrow_forwardIf we wanted the display to light up the left seven segment LEDs instead of the right ones, what would we change? What is the significance of the "Anodes" (AN0, AN1, AN2, and AN3) ?arrow_forward
- Give the verilog and testbench code. If a combinational circuit for a BCD to seven-segment code converter that will input a BCD number and output it on a seven segment common- anode display. The code converter will only display the number 8. The converter wil turn the display OFF for all other valid BCD digits except digit 9 which will never occur.arrow_forwardChoose the true H-bridge motor statements in the list below. O The L298N has a PWM input signal that can be used to control the motor direction. (false, it controls the speed of the motor. O You should always transition through the "Off" state when changing direction with the H-bridge. O The H-bridge provides a means of controlling a motors spin direction. O If all four H-bridge switches are open, the motors will spin. O The H-bridge uses four switches to control the current flow.arrow_forwardQ3. A door sensor is connected to P0.5 pin, an LED to P1.5 pin and a buzzer to P2.5 pin. Write an 8051 C program to monitor the door sensor such that when it is opened, the LED will blink and the buzzer will sound every 500ms, otherwise, when the door is closed, both of the LED and buzzer will be OFF.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning