How many 5/8 in A325 bolts in long slotted-size hole with slot parallel to the direction of bearingforce and with threads excluded from the shear plan are required for the bearing type connectionshown in figure (4)? Use fu = 58 ksi and assume edge distance to be 2 in and the distance center tocenter of holes to be 3 in. Assume that the deformation at bolt holes is a design consideration. Pu =450 k.11/4 or 1/422222222-in PL+-in PL2 in3 in2 inFigure (4)5/8 in bolt-in PLP or Pa

Given Data:1.) Bolt diameter, d=5/8d = 5/8d=5/8 in2.) Ultimate tensile strength of bolts, fu=58f_u…

Answered: How many 5/8 in A325 bolts in long…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. %3D 50, 100 100 99.45 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A - 3065 mm- y - 50.55 mm Fy - 248 MPa Fu 400 MPa Determine the design strength due to yielding in the gross section. (kN)
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. %3D 50, 100 100 99.45 T- 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm? y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the design strength due to fracture in the net section. UseU 0.85. (kN)
Situation 2. Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap conne ction. Bolt spacing are as follows: S1 = 40mm, S2 = 80mm, Sa = 100mm. Bolt hole diameter=25 mm 50 250mm 30 30 60 75 Allowable stress: Tensile stess on gross area of the plate=0.60 Fy Tensile stress on net area of the plate=0.5Fy Shear Stress of the bolt Fv=120MPA Bearing Stress of the bot Fp=1.2 Fu Calculate the permiss ible tensile load P under the following Conditions: 4. Based on shear capacity of bolts 5. Based on bearing capacity of bolts 6. Based on block shear strength (taking into consideration the failure path given in the figure below) 40 80 16 mm 40 180 mm 40 Bearing Failure Path #1 140 209 Bearing Failure Path #2
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: 2. Determine the nominal tensile strength of the 12 mm thick, A36 angle bar shown based on: a. Gross yielding b. Tensile rupture Bolts used for the connection are 20 mm in diameter. O O O O O O O Effective net area of the tension member if the shear lag factor is 0.80. Select the correct response: 1,516.1 1,354.4 1,431.2 1,221.6
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Plate t = 8mm C230x19.9 M20 Bolts Ag = 2,530 mm? d = 229 mm T 80 tw = 5.90 mm bf = 61 mm tr = 10.5 mm F, = 345 MPa x = 15 mm F = 450 MPa 60 80 80 60 From the figure shown, which of the following most nearly gives the block shear strength? O 679,7 KN O 1.013.8 KN O 872.9 KN 691.4 KN

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS