A butt joint shown in figure 3.29 is bolted using A 325 bolts with a diameter of 22 mm, with threads excluded from shear plane. Allowable shear stress F=207 MPa. Use A 36 steel with yield strength F= 248 MPa and a minimum tensile strength F₁ = 400 MPa. Assume diameter of bolt hole to be 25 mm. (1) Compute the shear capacity of the butt joint. (2) Compute the bearing capacity of the butt joint. Compute the tearing capacity of the butt joint. (3) TR 712 72 TR 22 num A 325 boll 125 mm x 300 00004 22 mm x 300

A butt joint shown in figure 3.29 is bolted using A 325 bolts with a diameter of 22 mm, with threads excluded from shear plane. Allowable shear stress F=207 MPa. Use A 36 steel with yield strength F= 248 MPa and a minimum tensile strength F₁ = 400 MPa. Assume diameter of bolt hole to be 25 mm. (1) Compute the shear capacity of the butt joint. (2) Compute the bearing capacity of the butt joint. Compute the tearing capacity of the butt joint. (3) TR 712 72 TR 22 num A 325 boll 125 mm x 300 00004 22 mm x 300

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 25 mm= DIAMETER OF BOLTS 45 45mm fmmy C. 90mm 90mm 90mm Comm P
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate is 800 mm² and the yield strength of the steel is 260 MPa. The ultimate shear strength of the bolts is 570 MPa. A factor of safety of 1.67 with respect to yield is required for the plate. A factor of safety of 4.0 with respect to the ultimate shear strength is required for the bolts. Determine the minimum bolt diameter required to develop the full strength of the plate. Note: consider only the gross cross-sectional area of the plate-not the net area. Support Plate ↓ P
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area c. Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 90m²m 90 mm 90mm 45 45mm In my comin P Scanned with CamScanner CS
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.
A L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answers
Situation 2. Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap conne ction. Bolt spacing are as follows: S1 = 40mm, S2 = 80mm, Sa = 100mm. Bolt hole diameter=25 mm 50 250mm 30 30 60 75 Allowable stress: Tensile stess on gross area of the plate=0.60 Fy Tensile stress on net area of the plate=0.5Fy Shear Stress of the bolt Fv=120MPA Bearing Stress of the bot Fp=1.2 Fu Calculate the permiss ible tensile load P under the following Conditions: 4. Based on shear capacity of bolts 5. Based on bearing capacity of bolts 6. Based on block shear strength (taking into consideration the failure path given in the figure below) 40 80 16 mm 40 180 mm 40 Bearing Failure Path #1 140 209 Bearing Failure Path #2
An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. %3D 50, 100 100 99.45 T- 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm? y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the design strength due to fracture in the net section. UseU 0.85. (kN)
A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six 16 mm diameter bolts to the 100 mm of leg to transfer tension as shown in figure. What will be the block shear strength (in kN) of the angle section assuming that the yield and the ultimate stress of steel used are 250 MPa and 410 MPa respectively? ISA (100 × 75 x 6) -T 16 mm o bolt 10 mm 40 mm 40 mm| 40 mm 40 mm 40 mm 40 mm 10 mm