How does project costs usually prepared?
Q: Question 6 A straight bar is fixed at edges A and B. Its elastic modulus is E and cross section is…
A: A straight bar fixed at edges A & B as shown- Elastic modulus = E, Cross-section area=A, Load…
Q: Determine the degree of indeterminacy for each of the following structures:
A:
Q: The cantilevered beam shown below is subjected to a vertical load P at its end When E is 70,000 MPa,…
A: δmax is the maximum deflection of the beam P is the vertical load = 5728 N L is the length of the…
Q: The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in…
A:
Q: A trapezoidal weir of length 4 m and sides inclined 1 horizontal to 1.5 vertical discharges 12 m³/s.…
A:
Q: Design a one-way slab having a simple span of 3m. The slab is to carry a uniform live load of 7,500…
A: Given Data: Span of one way slab=3000 mmf'c=27.6 MPafy=276 MPaLive load of slab=7500 PaFor main…
Q: The discharge in m³/s for laminar flow through a pipe of diameter 0.04 m having a centre line…
A: Diameter of pipe d =0.04 mCentre line velocity Umax=1.5 m/sDischarge Q=??
Q: Determine the area and the centroid (x, y) of the area
A: In solid mechanics, there can be any possible shape of the cross-section, for analysis of various…
Q: a square footing is to be constructed on a uniform thick deposit of clay with a unconfined…
A:
Q: Why do you split the 7 KN load ?
A: For a three-point bending test on a simply supported beam. The load is applied on the midspan, no…
Q: A reinforced concrete tied column carries an axial dead load of 650 kN and an axial live load of 800…
A: Given Data: The axial dead load is 650 kN. The axial live load is 800 kN. The compressive strength…
Q: 0 0 Influent- Influent Influent Anaerobic Aerobic Influent- Return activated sludge Aerobic Anoxic…
A: This question is related to the Environment Engineering from Civil Engineering. In this question ask…
Q: Air is drawn into a small open-circuit wind tunnel as shown in Fig. Atmospheric pressure is 98.7 kPa…
A: Atmospheric pressure = 98.7 kPa Temperature = 27 °C Velocity = 50 m/sec.
Q: A weight of 500 T Newton hangs from a cable of length of 10 m diameter 2 cm and E = 200 GPa, then…
A: Weight, P=500π N Cable length, L = 10 m Diameter, d = 2 cm Modulus of elasticity, E=200 GPa=200×109…
Q: A steel bar of 50 mm × 50 mm square cross-section is subjected to an axial compressive load of 200…
A:
Q: You are designing an afterburner to treat 2 m³/s of air at 1.02 atm and 20 °C. The pollutant…
A: To solve this problem, we need to use the principles of combustion and gas dynamics. Here are the…
Q: Design bond stress in limit state design method for deformed bars conforming to IS :1786 and M-20…
A: Deformed bars- M-20 concrete To Find- The design bond stress in LSM as per IS:1786.
Q: Please answer the rest of the questions
A: Note: As per Bartleby guidelines, only first three questions will be answered. Since first question…
Q: A circular log of 156mm diameter carries a 26KN load at midspan over a 3m simple span . If the…
A: Diameter of circular log = 156mm load = 26kN Length of span = 3m E = 7310Mpa It has been asked in…
Q: A soil has bulk unit weight of 20kN / (m ^ 3) and water content of 18%. Calculate the water content…
A:
Q: The flow ratio of a Francis turbine, if it is working under a head of 62 m and velocity at inlet 7…
A:
Q: E. Combined Flexure and Axial Example E.3: Second Order Bending and Axial Given: Braced column with…
A:
Q: A member of length 200 mm and diameter 25 mm is subjected to a tensile load of 20 kN. The final…
A: Length L=200 mm,Diameter d=25 mmLoad P=20 kNFinal length L'=220 mm. % increase in length=?
Q: A steel rod of 30 mm diameter and 3 m length is subjected to an axial pull of 50 kN. If E = 200 x…
A: A steel rod having, Diameter, D = 30 mm Length, L = 3 m or 3000 mm Axial load, P = 50 kN or 50000 N…
Q: 3. A recreational park is built near Buffalo Creek. The stream channel can carry 200 m³/s, which is…
A: Recreational park- peak flow =5 year flow of stream channel =200 m3/s
Q: Q7- For the soil profile and loading condition shown in figure. The final settlement of the clay…
A: Given data: unit weight of sand, γt=17 kNm3, γsat=20 kNm3 Unit weight of clay, γsat=21 kNm3…
Q: The average wastewater characteristics produced by a food processing plant are shown in Table A.2.…
A: Anaerobic treatment is a viable option for treating wastewater generated by food processing plants.…
Q: sing Unit Load Method, find the load (P) to make the horizontal deflection at point (C) equal to (10…
A: Deflection at point C = 10mm
Q: () Mass center and stiffness center of a structure is always the same. ( ) During a moderate…
A:
Q: Prob-4 Composites are materials that are made by embedding a fiber, such as glass or carbon, inside…
A: Sample size (n) = 28 Mean (x) = 0.42 Standard Deviation (S) = 0.04
Q: Calculate the difference in critical depth (in cm) corresponding to a discharge of 6.0 m³/s in a)…
A: Discharge, Q = 6 m3/sec Rectangular channel width, B = 3 m Critical depth=?
Q: A reservoir of glycerin (glyc) has a mass of 1200 kg and a volume of 0.952 m². Find the glycerin's…
A: Given :Mass of glycerin, m=1200 kgVolume of glycerin, V=0.952 m3
Q: Please only use these given ratios/formulas: γsat = Wsat / V w = Ww / Ws Gs = Ws / Vs γw γw = Ww /…
A:
Q: Grades of g -2.50% and 9 +1.50 %, VPI elevation 856.00 ft at station 22+00, and a fixed elevation…
A: The initial grade (g1) = -2.50% The initial grade (g2) = + 1.50% The elevation of PVI = 856 ft The…
Q: A vertical cut is supposed to be made through a clayey soil layer as shown below. The water table is…
A:
Q: For the following structure, please draw the normal force, shear force and the bending moment…
A: Given Required : Normal force, shear force and bending moment diagram
Q: How can civil engineers design and construct efficient and sustainable transportation systems, such…
A: Context: High speed trains or hyperloops
Q: The load P on a concrete foundation is applied through a steel plate as shown below. Steel plate is…
A: Stress is expressed as the ratio of force per unit area. Shear stress causes in a structure due to…
Q: 1. (a) Determine the internal normal force, shear force, and moment at point C in the double…
A:
Q: A hydraulic jump is formed in a 2 m wide rectangular channel which is horizontal and frictionless.…
A: A wide rectangular channel- Width of the channel b=2 m, Post jump depth y2=0.8 m/s, Post jump…
Q: Question-2: The cross section of the bar in the figure a) Calculate the stress(tension) values at…
A: Find: (a) Stress at points A, B, C (b) Stress distribution in the section
Q: Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in…
A: Pipe diameter, d1 = 50 mm or 0.05 m Flow rate, Q = 2 L/s or 0.002 m3/s Tap diameter, d2 = 15 mm or…
Q: Requirement: Check the adequacy of the following: 1. Girder 300 mm x 400 mm For Flexure, Shear, and…
A:
Q: Determine the Moment at B, for the Frame shown below. Assume at A and C is fixed. El is constant. 6…
A:
Q: A-2.40% grade meets a +1.60% grade at station 44+25 and elevation 3387.96 ft, 400-ft curve, stakeout…
A: The initial grade of the curve = -2.4% The final grade of the curve = +1.6% The station of point of…
Q: A rigid pavement is designed with a 9 inches slab and a subbase of 10 inches. The seasonal variation…
A: Sub base= 10 inch slab= 9 inches
Q: a square footing with a size of 10 ft by 10 ft is located 8ft below the ground surface. the subsoil…
A:
Q: Determine the horizontal displacement of joint C. A L B The length, L, of trusses AC, BC is 1,500…
A:
Q: Internal diameter of a steel shaft is 70% of external dia and the shaft has to transmit 3500 kW at…
A: Internal diameter of a steel shaft is 70 % of external dia. di=0.7do Shaft transmitted power, P =…
Q: e shaded area shown in (Figure 1) is bounded by the =y=zm and the curve y² = 1.2 m², where x is m.…
A: a=1.2m y2=1.2x and y=x
How does project costs usually prepared?
Step by step
Solved in 3 steps
- The construction schedule is the only project document that fully communicates the contractor's intention for delivering the contracted scope of services over the full course of the project duration. What,specifically, does it accomplish?give details.7. Discuss what are the primary ways in which project managers use estimates throughout the project? Explain in detail.Relate in practice methods/combination of charges for engineering services(you can select type of Project).