he steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be oplied to the ends of the shaft without exceeding a shear stress of 70071776 Pa and angle of twist of 2.37°. Use G = 3000000000 Pafor the shaft, x = 2.07 m, and y = 1.89 m. Round off the final answer to two decimal places. T ... 100 mm 70 mm 70 mm y

Q: 3k 30lbs 40° 40°

A:

Q: Identify the components of each force along the x and y axes portrayed in the photo.

A: Free Body diagram

Q: answer

A: A jet strikes a curved plate at its ______ a) Sides b) Surface c) Centre d) Does not strike

Q: Calculate a) reactions b) shear stress c) bending moment diagrams 5 ton E 4 m

A:

Q: Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN.…

A: FOR SAE 1040 hot rolled section yield stress is given byσy=415mpawe have σy=PAreaArea=π4d2d=dia

Q: 50kN 100kN 50kN H. 1m D. /// Im Im Im Im Tigure 1

A:

Q: Express each force as a Cartesian vector and calculate the resultant force.

A: Given:- Forces;              Determine:- Resultant force using Cartesian vector.Cartesian Vector:-…

Q: True or False?  When you/I cut through a rigid body or a truss that was previously in static…

A: Initially body is in static equilibrium. Static equilibrium - When the net force acting on body is…

Q: Given that the three bars shown in the accompanying figure are made of the same material, comparing…

A: Given data- The given bars and their conditions have been shown below-

Q: Determine the resultant force at A. 2 ft Fc 490 lb FR= 600 Ib 6 ft 4 ft 3 ft B 4 ft 2 ft 4 ft

A: Following are the two forces at point A: FC = 490 lb FB = 600 lb

Q: Plane a-a is called the D.

A:

Q: - Using good structural scheme explain very well the term Determinate Structure.

A:

Q: Determine the magnitude of the resultant internal normal force acting on the cross section at C.

A: Given : Pipe assembly subjected to a force of 600 N at B To find - The normal force acting on the…

Q: ve the following problems: 1. Determine the force in each bar of the truss shown in figure caused by…

A: The load is lifted at constant velocity, the forces involve is similar to forces under static…

Q: How is the force calculated in the braces?

A: Using load, Average stress has to be calculated at first. Choose either tributary method or…

Q: Which of the following is the correct classification of beam? unstable stable and determinate…

A:

Q: At an initial temperature of 12°C, the bars are unstressed and was placed between two rigid and…

A: Since the supports are unyielding, temperature increase will tend to expand the bars and no external…

Q: Calculate the magnitude of the resultant support reaction at A. -Include direction (upward,…

A: To find support reaction

Q: influence of the bar diameter on the torsional stiffness?

A: Influence of bar diameter on torsional stiffness

Q: Make and Solve a problem involving the concepts of torsion Note: -Box the final answer

A: Solve the problem involving the concept of torsion.

Q: 4 m * 2 m * 2 kN 1.5 kN 10 m H B 10 m 3 kN G 10 m 3 kN LL 10 m FIND ALL THE FORCES IN THE BEAMS AND…

A:

Q: Determine whether each of the beams and frames below are externally determinate, indeterminate, or…

A: Given data in question  Structures  To find out  Indeterminacy  Note Ds= degree of static…

Q: alculate the force at each point of the structure due to the applied and rrounding forces, indicate…

A:

Q: Explain Kinematic and Static Indeterminacy for beams, frames and trusses.

A: Beams: The beam in is statically indeterminate to the first degree. For the stiffness method, the…

Q: Determine the resultant of the four forces and one couple which act on the plate shown. 2 m 5 m 60 N…

A: Given:- Four forces and a couple are acting on the plate The magnitude of the forces are = 60 N, 50…

Q: Question 2 beam below is subjected to a loads as shown. Cross Section - 150 mm - 1.5kN 0.4 m 2kN 150…

A: The given Beam Is A "Cantilever Beam" Total Length of the beam =1.2m There is Two point loads are…