The number of plastic hinges formed in the frame below for combined mechanism are 2W. B 3m 3m 1.5W 2 m A 4 m W ↓ 2 m Ꭰ

Q: Effective and Neutral Stress Question 4: The water level in a lake is 5m above the bed, and the…

A:

Q: :A. Find the discharge through the Venturi meter B. Find Different in pressure between 1&2 in…

A:

Q: A sample of a saturated soil has a water content of 25%. If the specific gravity of soil solids is…

A: Given- Water content w=25%, Specific gravity G=2.70, Saturated soil S=1, It is needed to find the…

Q: Answer f & g

A:

Q: Q- In a laboratory, a flow experiment is performed over a hydraulic structure. The measured values…

A: Given- Discharge- Q=0.05 m3/s,Velocity Vm=0.25 m/s,Lr=1/30,Qp=270 m3/s, It is needed to find the…

Q: 4) Two branches of different sections and discharges merge and continue to flow in a main channel…

A: Given data  For A and B channel dimension are given and slope also given..... So we can calculate…

Q: The simply supported beam ABCD is loaded by a weight W =27 kNthrough the arrangement shown in the…

A: FREE BODY DIAGRAM OF THE QUESTION;

Q: The laboratory test on a soil sample yields the following results: natural moisture content = 18%,…

A: Given data- Moisture content w=18%, Liquid limit wL=60%, Plastic limit wp=25%, %C=25%, To Find- The…

Q: Given a 3.5meter W6x25 steel column (Fy = 345MPa) with fixed-free support. Use ASEP steel manual for…

A: Given, L = 3.5 m or 3500 mm  W6 x 25 section  Fy = 345 MPa

Q: A 30 mm diameter rod made of a ductile material with a yield strength of 200 MPa is subjected to…

A: Given : Diameter of rod = 30 mm Yield strength = 200 MPa  Bending moment = 150 N-m This is a problem…

Q: hydraulic gradient of "2.5". The soil specimen has specific gravity of 2.65 and.... A constant-head…

A:

Q: If gravel voulme conversion factor is like below and bedding layer should ,be compacted

A:

Q: A bar of circular cross-section varies uniformly from a cross section 2D to D. If extension of the…

A: Given :  Variation of cross section  is from 2D to D This is a problem of solid mechanics where we…

Q: 380 mwak Q-24: A pipe of diameter d and length L leads from a reservoir. At the discharge end a…

A:

Q: For a fully-developed flow of water in a pipe having a diameter 10 cm, velocity 0.2 m/s, and kinetic…

A: Given Data  Diameter of pipe = 10 cm  Velocity of flow = 0.2 m/s  Kinematic viscosity = 10-5 m2/s…

Q: A camera with a focal length of 20 cm fitted in an aircraft is used for taking vertical aerial…

A: Given data- Focal length f=0.2 m, Height h=1200 m, S=1/8000, To Find- Height above MSL.

Q: Determine if the beam shown below will fail in tension or compression. Given fe= 4,000 psi fy =…

A: A) Given data : f'c = 4000 psi fy = 60000 psi To Find : Determine if the beam will fail in tension…

Q: Q2/ A steel rod is used to support a weight of (20 kN). If the allowable stress is (80000 kN/m²).…

A:

Q: For the beam below, solve for the reaction forces

A: GIVEN :   TO  FIND : reaction forces

Q: Determine the period for each of the steel special moment-resisting frames shown below using Method…

A: To determine - Time period by using method A of NSCP 2015

Q: The rigid frame shown in Figure is unbraced. The members are oriented so that bending is about the…

A: Given: DL = 50 kips LL = 150 kips  L = 15 ft Ky = 1.0 Beam section = W 18 x 50, Columns section = W…

Q: +6.00 m 0.00 m -10.00 m -18.00 m GWT 6.00 m 0.50 m Ysat 17.0 kN/m³ = Ysat 18.0 kN/m³ = BACKFILL Yn…

A:

Q: the influence line for -the reaction at support A and D -the shear and moment at E the moment at B…

A: ###Determination of ILD for Reactions At A and D and SF and BM at E and BM at B And C ####

Q: 4. A 1 m square, 0.5 m deep footing carries a downward load of 200kN. It is underlain by an…

A:

Q: 2. For a simply supported beam with a concentrated force, the coordinate system is selected as shown…

A:

Q: State three examples of a static load application and three examples of adynamic load application.

A: Static loading denotes a constant load placed on the structure over time. Static loads are typically…

Q: Situation 2. See Figure SM - 022 A permeable soil is underlain by an impervious layer. For the…

A:

Q: Question 3 Calculate the critical depth corresponding to a discharge of 8.5m³/sec in a rectangular…

A: Given data in question  Discharge 8.5 m3/s Width 3.6 m To find out  Critical depth

Q: 9. For the rigid frames shown in the Figure 4, determine the displacements and rotations of the node…

A: Given:- E=210 GPaA=2×10-2 m2I=2×10-4 m4 To find:- Displacements and rotations at node 2

Q: A retaining wall 8 m high with a smooth vertical back retains a clay backfill with C = 15 kN/m2², o…

A:

Q: Explain what you mean by "inner sifting."

A: Inner shifting is a process of change that happens within oneself. It is a movement from one state…

Q: A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (W_D1, W_L1) and…

A: Answer  1)  Calculation of height of compression stress block using pair 1 We know that Nominal…

Q: Water is pumped at steady uniform flow rate of 0.01 m3/s though a horizontal smooth circular pipe of…

A: Given: Water is pumped at steady uniform flow rate of, Q = 0.01 m3/s A horizontal smooth circular…

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

A:

Q: Find the forces in beam CD, JD and JK of the bridge shown in Figure 1 sections. Clearly state…

A:

Q: A cohesive soil yields a maximum dry density of 16 kN/m³ during a standard Proctor Compaction test.…

A:

Q: Х a W C a B

A: Solution: Ay+By=waMA=0By×2a=wa×a2By=wa4Ay=3wa4

Q: Problem 13: Determine the horizontal deflection at point D for the frame as shown in figure by…

A: Given : E = 2 X 105 N/mm2  I = 8 X 108  This is a problem of structure where we are asked to…

Q: Julia Vargas avenue in Ortigas, Pasig is classified by the DOTR as a Class I two-lane highway  on…

A: Answer  For given class I highway Level of service(LOS) depend on the percent time spent…

Q: For a town with a population of 2 lakhs, a water supply scheme is to be designed. The maximum daily…

A:

Q: A 50 year old 5 storey building is near a creek and railway. It is said that the building is leaning…

A: As an engineer, I would recommend the following regarding the foundation of a 50-year-old 5-storey…

Q: Q-7b,A rectangular open channel has a width of 5m and a bed slope of 0.001. For a uniform flow of…

A: Given- Width b=5 m, Bed slope S=0.001, Depth of flow y=2 m, Velocity V = 2m/s, Manning's roughness…

Q: Consider the beam with an overhang shown in the figure. a. Determine the shear force V and bending…

A:

Q: A trapezoid has its bases equal to 150m and 360m respectively. The base angles are 60 deg and 48…

A:

Q: Question 3 Calculate the critical depth corresponding to a discharge of 8.5m3/sec in a rectangular…

A: Given that :- Discharge = Q = 8.5 m3/s width = B = 3.6 m To calculate the critical depth

Q: For a portion of highway the Line AB meets BC, Point A is at a MSL of 2000 m and point B is at a MSL…

A: Given that :- t = 2.5 sec , f = 0.35 Point A is at MSL of 2000 m and point B is at MSL of 1999.9 m…

Q: On a motorway, the number of vehicles arriving from one direction in successive 5 seconds interval…

A: Given that :-             Vehicle arriving  in 5 seconds interval…

Q: A reservoir with a live storage of 300 million cubic metre irrigate 40000 hectares (1 hecatre = 104…

A: Given- Live storage=300 million cubic meter, Crop area = 40000 ha, Base period B=120 days, It is…

Q: Tie bars of 12 mm diameter are to be provided in a concrete pavement slab. The working tensile…

A: Given- Tie bars of 12 mm diameter, Tensile stress=230 MPa, Average bond strength = 2 MPa, Joint gap…

Q: For a design speed of 80 kmph, if the deviation angle of a valley curve is 1/20 then the length of a…

A: Given data in question  Design speed 80 kmph Deviation angle 1/20 Valley  curve To find out  Length…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.