he solid aluminum shaft ABCD carries the three torques shown. Determine: (a) the smallest safe diameter of the shaft if the allowable shear stress is 15 ksi. (b) Compute the angle of rotation of end A of the shaft using G = 4 x 10^6 ?

Q: The 56-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and…

A:

Q: 1000 Nom 1060Nom TITTITIIT

A:

Q: For the steel shaft shown in Fig. Determine the maximum torque transmitted by any transverse cross…

A: For better understanding Draw the schematic diagram of the above problem.

Q: A static shaft is subjected to torques at A, B, and C. It has a diameter of 58 mm and is made from…

A: The magnitude of angle of twist is The length of shaft  1 is The length of shaft 2 is The diameter…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: The allowable shear stress for brass shaft, The allowable shear stress for aluminum shaft, The value…

Q: A circular shaft with 50mm and its lenght is 850mm long and is made of steel, the shaft is subjected…

A: GIVEN :- diameter : d=50mm length: L=850 mm Torque subjected: T=800Nm (to determine θ we need the…

Q: The 54-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: 5. A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12 ksi. If the…

A:

Q: 4. The tapered shaft is made from E- 36 steel (G = 80 GPa ), and has a radius which can be described…

A: Given    Torque, T = 450 Nm    Length, L = 4 m Find     Angle of the twist

Q: me 30-mm-diameter A-36 steel shaft bjected to the torques shown. Determin e angle of twist of the…

A: Solution is attached below

Q: The 66-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and…

A:

Q: . If the shaft has an equilateral triangle cross section and is made from an alloy that has an…

A:

Q: must transmit the torque of 34 kN-m. The total angle of twist must not exceed 3°. The maximum…

A:

Q: Q.2) If the shaft is made of red brass copper with an allowable shear stress of Callow= 20 MPa,…

A: According to the information, we know the shaft is made of brass or copper road, The maximum…

Q: 2. In the gear system shown, the motor applies a torque of 600 N-m to the gear A. Shafts (1) and (2)…

A:

Q: The 60-mm-diameter shaft is made of 2014-T6 aluminum (G=27 GPa). If the allowable stress is Tallow =…

A:

Q: flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and…

A: The diameter of bigger circle is The diameter of smaller circle is The number of bolts on bigger…

Q: The copper shaft is hollow from A to B and the steel shaft is solid from B to C. The shaft has an…

A: Given that, Outer diameter of shaft, Do=100 mm,Thickness of shaft, t=20 mm,Modulus of rigidty of…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

A: Answer: The maximum allowable torque that can be applied to the ends of the shaft is 4.0042 kN•m.

Q: 75 mm D. 1.5 m E F B 2 m 150 mm 5 deg 2 deg 4 deg 1.5 deg 1 deg 3.5 deg

A: Write the twist angle of point A respect to point B.   φA/B=φA-φBφA-φB=3°…

Q: 1. The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown.…

A: Given data: d=40 mmShaft=A-36 steel Need to determine the angle of twist of end B with respect to…

Q: Compute the torsional shear stress (MPa) in a 45-in circular steel shaft with a diameter of 42-mm…

A: The length of the circular shaft, (L)=45 in.The diameter of the shaft, (D)=42 mm.The torque on the…

Q: The composite shaft below, consists of three sections, a tubular indication welded, through flanges…

A:

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: The 63-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: A steel shaft 2558 mm long must transmit a torque of 34 KN-m. The total angle of twist and the…

A:

Q: A steel shaft is fixed at A and is subjected to the torques as shown. Segment AB has a diameter of…

A:

Q: The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure Part A If the allowable…

A: Givend=60mmτallow=80MPaθA/Callow=0.060 rad

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A:

Q: A body is moving in a curved path with speed of 10 m/s and tangential acceleration of 3 m/s2. If…

A: Given, Speed of the car = v = 10 m/s Tangential acceleration = at = 3 m/s2 Radius of curvature = r =…

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: Solid shaft can resist a bending moment of 8.0 kNm and twisting moment 10 kNm together. Determine…

A: Given data,  For solid shaft,  T=10 kNm  M= 8 kNm  Need to find maximum torque Tm

Q: If T = 600 Nm, determine the absolute maximum shear stress in the shaft (in MPa) b. If the maximum…

A:

Q: Both shafts have the same diameter-2cm and are made of low quality steel G-77 GPa. A torque of 1200…

A:

Q: If the chaft shown in Figure is made of one material and is subjected to torques TI-25 kN.n and…

A:

Q: 1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 Ib-in. The total angle…

A: Given data: The transitted torque, T=300000 lb·in. The shear modulus, G=12000000 psi. The angle of…

Q: If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa,…

A: allowable stress = 20 Mpa  Length = 0.75 m  Modulus of rigidity G =37 GPa

Q: A steel shaft 2550 mm long must transmit a torque of 34 KN-m. The total angle of twist and the…

A:

Q: A flanged bolt coupling consists of ten 15-mm diameter bolts spaced evenly around a bolt circle 350…

A:

Q: 1. The solid line shaft in Fig. 1 is made of steel and transmits the input power of 35 kW at pulley…

A: The Answer is Below

Q: A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m.…

A: Given      Diameter, d = 60 mm  Torque load, T = 8.7 kN•m

Q: A solid shaft can resist a bending moment of 4 kN-m and a twisting moment of 5 kN-m together.…

A:

Q: If allowable shear stress in the shaft is 80N/mm? and the torque equivalent(Te) is 1.23 x106 N-mm.…

A:

Q: ix 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel and six 20 mm diameter…

A:

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: Given:Outside diameter of brass shaft, d1=0.51 inAllowable shear stress for brass, S1=4500…

Q: The composite shaft consists of a mid-section that includes the 1-in.-diameter solid shaft and a…

A: In centre torque will be divided in such a way that angle of twist in section AB in tube ans shaft…

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.