V:..H.W. .mp4www.DANDICAMCOH.W. 1 Poly-phase SystemsA three phase, four-wire, 208 volt, CBA system has a wyeconnected load with Z, = 60°,2, = 6/30° and Ze = 5/45°. Obtain the three line currents and the neutral current(in a polar form)after finding O2 and 03.A'120/031002B-120/150

The solution can be achieved as follows.

H.W. 1 Poly -phase Systems A threephase, four-wine, 208 volt, CBA ystem has a wyeconeted load with Z, = 60°, 4 = 600 and e = 545°. Obain the thre line curents and the neutral curent(in a polar form) after finding 02 and 03.

H.W. 1 Poly -phase Systems A threephase, four-wine, 208 volt, CBA ystem has a wyeconeted load with Z, = 60°, 4 = 600 and e = 545°. Obain the thre line curents and the neutral curent(in a polar form) after finding 02 and 03.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Related questions

Q: Each line of a 3-phase system is suspended by a string of 3 similar insulators. If the voltage…

A: given voltage across string unit=17.5kv no of insulator=3 shunt capacitance 1/10 th of the…

Q: An AC three phase distribution system (given in Figure 2), which has end user with balanced three…

Q: A 30 mile, 3-phase transmission line delivers 8,000 kW at 33 kV, p.f. 0.8 lagging. The resistance…

Q: b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance…

Q: Q5: A SL-G fault occurs on the low voltage side of a transformer that connects a motor to a…

A: Given data for generator, Given data for motor,

Q: Question 1: A three-phase, three-wire, 240 volt, CBA system supplies a delta-connected load in which…

Q: Q3: A three phase, four wire, 208 volt, CBA system has a Y-Y connected load with A-6 , ZB-6230°, and…

A: In the question, Four wire 3 phase system given Phase sequence CBA. Find the line current and…

Q: 3-phase, 126 MVA, 132 kV, 50 Hz, 355 mm² underground cable of outer radius 18 mm. Note: consider…

A: Given data, The supply frequency = 50Hz Area of the underground cable = 355mm2 The radius of the…

Q: (ii) tränsmission efficiency *. Estimate the distance over which a Joad of 15000 kW at 0-85 n f can…

Q: The capacitance between the line to neutral of a three-phase 50 Hz, 66KV overhead line conductors…

A: Frequency is given f = 50 Hz Capacitance is given C=8.3×10-7 Farad/ph/m Capacitive reactance is…

Q: 2. A three-phase, three wire, CBA system with an a line voltage of 100 Volt, has three impedances of…

A: It is given that: VL=100Z=5∠30° Ω

Q: c) A 3-phase system has conductors arranged symmetrically as shown below: May D D The symmetrically…

A: In this question we will find line to neutral capacitance and capacitive current for 3 phase…

Q: A 3-phase transmission line operating at 33 kV and having a resistance of 5 2 and reactance of 20…

A: Given data, Sbase=15,000 kVASbase=15 MVA Single line diagram of the system,

Q: Under Unbalanced Condition Without Faults: a. Load Line Currents (Ia, Ip,I); b. Load Line Voltages…

A: We are authorized to answer three subparts at a time. Since you have not mentioned which part you…

Q: Q1. What is the necessity of maintaining phase sequence? Suppose there are three loads connected at…

A: Given data: VR=1200 VVL=2400 VVC=2400 V

Q: a single phase overhead transmission line delivers 4000k w at 11 kV at 0.8 pf lagging. If resistance…

A: First we will calculate receiving end current from given values, using formula we will find sending…

Q: onsider the above approximate equivalent circuit for IM. A six-pole, 220Volt (line to line), 50Hz,…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: 1. In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage…

A: Given voltage across top and middle units, using this we will find Ratio of capacitance, string…

Q: Q: 3 Figure below shows a 735 kV three-phase transposed line composed of four ACSR, 954, 000- cmil,…

A: Given: Geometric mean radius, GMR= 1.173

Q: 3. A three-phase, three wire, CBA system with an a line voltage of 150 Volt, has three impedances of…

Q: Task-2 A radial feeder is shown in Figure 1. -3-Phase Transmission Line Bus-A Bus-B Bus-C Bus-D CB,…

A: According to question, we have designed the CT ratio, estimated the time of operation for all three…

Q: 12500kva load is supplied at a power facter of 0.8 lagging by a 3 phase transmissiom line whose…

A: We can draw the power system as here load is PR+jQR=12500×0.8 kW+j12500×0.6kVAR=10000kW +j 7500kVAR…

Q: Draw the developed diagram of a 3-ph, 6-pole, chain winding. The number of slots per pole per phase…

A: Chain winding is a type of distributed winding with a diamond shape and having an equal length of…

Q: A commercial Building, 60hz, Three Phase System, 230V with total highest Single Phase Ampere Load of…

A: Given :f = 50 Hzv = 230VP = 25 Hp1-ϕ → IL = 1088 A3-ϕ → IL = 206 AIFL = 68 A

Q: A 100 km Three-Phase 50 Hz transposed transmission line is çomposed of bundle of three ACSR,…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Question 2) A 100 km Three-Phase 50 Hz transposed transmission line is composed of bundle of three…

A: As per our policy we can provide solution for first question only. As we have given : GMR1=1.5…

Q: Q1 : in a 3-phase, 4-wire system , the curents in a, 6 and c lines under abnormal Condiions of…

A: In this question we will find sequence components of line current I a...

Q: The capacitance between the line to neutral of a three-phase 50 Hz, 66KV overhead line conductors…

A: In this question, line to neutral capacitance is given for horizontal configuration..We have to find…

Q: Consider the same 4-bus system shown. Use the tie set method to determine the reliability,…

Q: Electric Machine; Check image, all question there. Consider the above approximate equivalent…

A: Given Data: R1=0.5Ω , R2=0.25 Ω, X1=0.75 Ω, X2=0.5 Ω, Xm=100 Ω, Rc=500 Ω

Q: The resistance and reactance of the single-phase 60Hz transmission line conductors are 5.4 ohm and…

Q: The resistance and reactance of the single-phase 60HZ transmission line conductors are 8.8 ohm and 9…

A: Given single phase transmission lineResistance R=8.8 ΩReactance XL=9 ΩReceiving end voltage VR=56…

Q: A synchronous generator is feeding its rated power of 250 MW to a large 60 Hz network over a double…

A: We will use equal area criteria to find stability of system. During 3 phase fault occures power…

Q: 5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a…

A: Given: 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz. R1=0.21Ω, R2=0.18Ω,…

Q: The capacitance between the line to neutral of a three-phase 50 Hz, 66KV overhead line conductors…

A: Find the capacitive reactance of transmission line? If capacitance c = 7.7×10-7 F/ph/m…

Q: The sequence component line-to-line voltages of a three-phase, 4-wire system are the following: Vab0…

Q: A commercial Building, 60hz, Three Phase System, 230V with total highest Single Phase Ampere Load of…

A: Solution- Given, V = 230 VI1 = 1088 AI2 = 206 AI3 = 68 A a) IT =I1+I2+I3IT =1088+206+80 = 1362 A…

Q: The figure below shows a 'go' and 'return' conductor of a single-phase power distribution line. If…

Q: Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: A three phase transmission line has horizontal configuration with a spacing of 6 meters between…

A: Choose the correct option What is value of inductive reactance for the 1kM . We know inductance L…

Q: 2. A three-phase, three wire, CBA system with an a line voltage of 100 Volt, has three impedances of…

A: In this question three phase star connection is given....We have to find out line current , power…

Q: Q#1: In a 3-phase, 4-wire system, the currents in R, Y and B lines under abnormal conditions of…

A: We’ll answer the first question since the exact one wasn’tspecified. Please submit a new question…

Q: In a 380 kV three-phase transmission system, the diameter of the overhead lines in the form of…

A: Part (a): The line voltage is given as 380 kV. The disruptive critical voltage is determined as:…

Q: The resistance and reactance of the single-phase 60HZ transmission line conductors are 5.4 ohm and…

A: Note: As per guidelines will be solving only first 3 subparts. Repost for others For the given data…

Q: 1. A delta connected load with impedance 20cis0- ohms per phase is supplied from a 220 volts, 60…

Q: In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across…

A: Given three phase overhead system , each line is suspended by a string of 3 insulators The voltage…

Q: Athree-phase, 60-Hz, 500-MVA, 11.8-KV, 4-pole steam turbine-generating unit has an H constant of 6…

A: The information are provided as:

Q: The capacitance between the line to neutral of a three-phase 50 Hz, 66KV overhead line conductors…

A: Capacitance between line to neutral C= 8.5×10-7 F/ph/m Frequency f= 50Hz Reactance Xc ?

Q: transmission line has a resistance of

A: Insulator in transmission line- The device used to protect transmission line and prevent the…

Q: In a 3-phase, 4 wire unbalanced system, the current in neutral wire is 18 A. The magnitude of zero…

A: Given a 3-phase, 4 wire unbalanced system having, The current in neutral wire, IN=18 A

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

V:..
H.W. .mp4
www.DANDICAMCO
H.W. 1 Poly-phase Systems
A three phase, four-wire, 208 volt, CBA system has a wyeconnected load with Z, = 60°,
2, = 6/30° and Ze = 5/45°. Obtain the three line currents and the neutral current(in a polar form)
after finding O2 and 03.
A'
120/03
1002
B-
120/150

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Solution

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The mutual inductance coupling coefficient standard unit is .. * Ohm Henery O Unit-less Mho
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
Consider a 3-phase, 50 HZ, 11 KV distribution system. Each of conductors is suspended by an insulator string having two identical porcelain insulators. The self-capacitance of the insulator is 5 times the shunt capacitance between link and ground. Find the voltages across two insulators.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
Which of the following statements is/are true? (A In purely inductive circuit, the current leads voltage. (B) In purely resistive circuit, the current lags voltage. C In purely resistive circuit, the current is in phase with voltage. D In purely capacitive circuit, the voltage lags current.
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator