H.W/ By using ASD and LRFD methods, find a light section W12xw of A992 steel material of member BC in the figure below assumed the connection at the flange of two lines (6 %). Key of solution: The distance between A and C is 17.3 feet After analysis the forces.... BC-323.4 kip. 20¹ B 280' kip, 10⁰

H.W/ By using ASD and LRFD methods, find a light section W12xw of A992 steel material of member BC in the figure below assumed the connection at the flange of two lines (6 %). Key of solution: The distance between A and C is 17.3 feet After analysis the forces.... BC-323.4 kip. 20¹ B 280' kip, 10⁰

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Homework: A helica) cast steel with 3. helix angle has to tanmiz 35 KW at 1500 YPu. Gear has 24 teeth, 2 full depth. Tha Static Stress for Cast Steel maybe taken as 56 Mpa.. The width. of face may be talcen as 8 time) th module. Assum e : Cs =l, Ep=E= Ges=300 HPa , be =60 MPa, Calculate: WA, WNm, b, VR, = 200G Pa C=40.
Please solve this problem in double integration method
IDENTIFY THE ZFM ZERO FORCE MEMBERS
In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.
Strength of Materials (Upvote will be given. Please write the complete solutions and FBDs Legibly. No long explanation needed. Solve in 3 decimal places.)
only HANDWRITTEN answer needed ( NOT TYPED)
Use the subsne member to make a compieneanlyss of e comples uss shown 25kN d 3m 25KN 4 m e1.5 m 2 at 4 m = 8 m
only Find Neutral Axis (NA). please in detail.
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE
Answer 15&16