4 m96 kN75 x 75 x 6 mm200Gm4 mkN 96 kN14 mmgussetplate75x75x13 mmFacPaeFigure shows a roof truss and the detail of the rivetedconnection at joint B. Using allowable stresses of t = 90 MPaand o = 160 MPa;(a) how many 19mm diameter rivets arerequired to fasten member BC to the gusset plate?(b) how many 19mm diameter rivets arerequired to fasten member BE to the gusset plate?

Answered: Image /qna-images/answer/4512c158-65fa-4f07-9c38-9cf898200d1b.jpg

Gm Ha 4 m 4 m 200 kN 96 kN 96 kN 75 x 75x 6 mm 14 mm gusset plate 75x75x13 mm Pac Pac Figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 90 MPa and a = 160 MPa; (a) how many 19mm diameter rivets are required to fasten member BC to the gusset plate? (b) how many 19mm diameter rivets are required to fasten member BF to the gusset plate?

Gm Ha 4 m 4 m 200 kN 96 kN 96 kN 75 x 75x 6 mm 14 mm gusset plate 75x75x13 mm Pac Pac Figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 90 MPa and a = 160 MPa; (a) how many 19mm diameter rivets are required to fasten member BC to the gusset plate? (b) how many 19mm diameter rivets are required to fasten member BF to the gusset plate?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Montebon, Jamaica Mge B PIate No lo Vir tyal Wor k Method (Trusses) ID No. 16-0893-335 #1. Determine the vertical dispiacement Of joint A-Each bar is made of steel qnd has a crass-sectional area Of 600 mm?. Tqke E = 200 CPQ.use the me thad of virtual wark. use P Last 2 digits of ID NO. 2: 5th digit of ID NO. P 35 a=9 D. 1-5m - 1-5m- p 35
4. Six rivets are used in the connection shown in the figure. If both P= 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Ps so 100 mm
Six rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
A76 x 76 x6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy-248MPA and Fu -400MPA. Gusset Plate Alowable Sresse Alowable tensle stress igross ara)0.00 Alowable tereile stres net area)0SOF. Allowable shear stress (net ares)0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85% O 138.24 KN O 140.14 kN O 157.93 kN O 304.00 N Next
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine: a. The shear stress in the bolts. Answ. 11.81 ksi b. The axial stress in the bolts. Answ. 23.62 ksi c. The support stress in the W12X65 profile. 11.50 ksi
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Peso 100 m
"messenger_media?thread_id%=D100002917920802&attachment_id%3891210971774069&message_id%3Dmid.%24CAAAA Question 3 For the truss shown, determine the forces in members (a) BD; and (b) BF. 4 m4 m4 m-4 m- A B C 6 m E F G H O00 20 kN 20 kN 20 kN A BD-40kN (C); BF-33.33kN (T)
6. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24mmp A490N bolts. The plate is A36. Determine the safe load Pu using LRFD that the truss can resist according to the capacity of the connection. 15 15 с 1.5 3P. + D 1.5 80 mm 70 mm 70 mm 80 mm Fac 7. Repeat Problem 6 using 30mm A325-N bolts and A-50 steel. Use ASD. 50 mm Fac
8) what is the flexural rupture capacity of the shear plate of the shear connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
2. Determine the adequacy of the clip angle connection shown. The allowable stresses are 100 MPa for shearing, 220 MPa for bearing, and 140 MPa for tension for the seat angle and the rivets. 45 kN 220 mm I 16 65 32 150 150x100x16 clip angle 20 mm o rivets 16 100
5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi