Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine heat transfer rate for the heat exchanger. Determine the outlet temperatures of both fluids.

Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine heat transfer rate for the heat exchanger. Determine the outlet temperatures of both fluids.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.32P

See similar textbooks

Similar questions

Water flowing in a long, aluminum lube is to be heated by air flowing perpendicular to the exterior of the tube. The ID of the tube is 1.85 cm, and its OD is 2.3 cm. The mass flow rate of the water through the tube is 0.65kg/s, and the temperature of the water in the lube averages 30C. The free-stream velocity and ambient temperature of the air are 10m/sand120C, respectively. Estimate the overall heat transfer coefficient for the heat exchanger using appropriate correlations from previous chapters. State all your assumptions.
10.1 In a heat exchanger, as shown in the accompanying figure, air flows over brass tubes of 1.8-cm 1D and 2.1-cm OD containing steam. The convection heat transfer coefficients on the air and steam sides of the tubes are , respectively. Calculate the overall heal transfer coefficient for the heal exchanger (a) based on the inner tube area and (b) based on the outer tube area.
What is the main difference between a copper and a cupronickel coaxial heat exchanger, and where is each used?
Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine Cmin and Cmax Find c, e, and NTU Determine heat transfer rate for the heat exchanger. Determine the outlet temperatures of both fluids.
Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine Cmin and Cmax Find c, e, and NTU
A shell and tube heat exchanger is designed as a counter to cool a mass flow rate of 60 kg/h of engine oil (cp = 1060 J/kg oC) from 300oC to 150oC. The cooling water, cp = 4182 J/kgoC, enters the tube side (Length is 1.75 m and Outer diameter is 2.54 cm) at a temperature of 20oC. If the overall heat transfer coefficient, U, is 10.83 W/m2o C and the Capacity Ratio of the Heat Exchanger is 2.4, calculate the following: a)The heat transfer rate,b)The mass flow rate of the cooling water in the units of (kg/h),C)The surface area of the heat exchanger,
An analysis is performed to determine the heat transfer coefficient of a oil-to-water, one-pass countercurrent shell-and-tube heat exchanger It has 24 tubes with an internal diameter of 1.2 cm and a length of 2 m. Cold water (cp= 4180 J/kg K) enters the tubes at 20°C at a rate of 3kg/s and leaves at 55°C. Oil (cp=2150 J/kg K) flows through the shell as it cools from 120°C to 45°C. determine the overall heat transfer coefficient U of this heat exchanger, based on the inner surface of the tubes.
Water enters a body-tube heat exchanger as a hot fluid at a flow rate of 2.6 kg/s at 68 °C. The cold fluid is water at a flow rate of 1.8 kg/s and the inlet temperature to the heat exchanger is 32°C. Calculate the outlet temperature of the cold stream since the heat exchanger efficiency is known as 0.55. NOTE: For water, cp=4179 J/kg.K will be taken as constant.
DU - Moodle English (en) A counter-flow double pipe heat exchanger shown in the figure below is to heat water from 20°C to 100°C at the rate of 1.2kg/s. The heating is to be accomplished by geothermal water available at 160°C at a mass flow rate of 2kg/s. the inner tube is thin-walled and has a diameter of 1.5 cm. If the overall heat transfer coefficient of the heat exchanger is 640W/m². °C. The specific heat capacities of the water and geothermal are 4.18 KJ/Kg. °C and 4.13 KU/Kg."C respectively. Determine heat transfer in the hot water. on Hot geothermal water 160°C 2 kg/s Cold water 20°C 100 °C 1.2 kg/s D = 1.5 cm Select one: О а. 40.128KW O b. 40128KW O c. 4.0128KW O d. 401.28KW
A shell-and-tube heat exchanger consists of a single shell and 10,000 tubes of 35 mm diameter, each executing two passes. The heat exchange is accomplished by passing the cold fluid ( Cc=1.05x107W/K) entering at 25°C through the thin-walled tubes and leaving at 42°C. The hot fluid (Ch=14x106W/K) is entering at 62°C and the overall heat transfer coefficient U is equal to 3000 W/m2.K. What is the required tube length per pass? Select one: a. 3.2 m b. 1.6 m c. 10 m d. 5 m
5. Hot exhaust gases, which enter a finned-tube, cross-flow heat exchanger at 300 °C and leave at 100 °C, are used to heat pressurized water at a flow rate of 1 kg/s from 35 °C 125 °C. The specific heat of water at the average water temperature is 4197 J/kg. K. The overall heat transfer coefficient based on the gas-side surface area is Uh = 100 W/m².K. Determine the required gas-side surface area A₁ using the LMTD and & -NTU method.
1. A long thin-walled double-pipe heat exchanger with tube and shell diameters of 1.0 cm and 2.5 cm, respectively, is used to condense refrigerant-134a by water at 20 0C. The refrigerant flows through the tube, with a convection heat transfer coefficient of 5000 W/m2 K. Water flows through the shell at a rate of 0.3 kg/s. Determine the overall heat transfer coefficient of this heat exchanger. If a 2-mm-thick layer of limestone (k = 1.3 W/m K) forms on the outer surface of the inner tube what will be new overall heat transfer coefficient