An initially empty tank on Earth is being filled with water so that the height of the water in the tank increases at a steady rate. Which one of the following graphs best describes the gauge pressure P at a point on the bottom of this tank as a function of time t during the filling process? Assume the tank starts filling at time t = Os and that the top of the tank is open to the atmosphere. The atmospheric pressure does not change during the process. The water in the tank does not overflow or reach the top of the tank during this process. A) B) D)

An initially empty tank on Earth is being filled with water so that the height of the water in the tank increases at a steady rate. Which one of the following graphs best describes the gauge pressure P at a point on the bottom of this tank as a function of time t during the filling process? Assume the tank starts filling at time t = Os and that the top of the tank is open to the atmosphere. The atmospheric pressure does not change during the process. The water in the tank does not overflow or reach the top of the tank during this process. A) B) D)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A liquid storage tank consists of a vertical axis circular cylindrical shell closed at its lowered end by a hemispherical shell as shown in the figure. The weight of the system is carried by a ring like support at the topand the lower extremity is unsupported. A liquid of specific weight of 9KN/m^3 entirely fills the container. Consider H = 8m, R =2.4m, and plate thickness of 1.8mm. a.Find the peak stress in the hemispherical region. b.Calculate the peak circumferential stress in the cylindrical region. **Note = Pressure = specific weight x height Show free body diagram
Problem 5 In the figure shown, what is the static pressure in kPa in the air chamber? AIR 2.0 m OIL 4.0 m S=0.80 5.0 m WATER 3.0 m
This closed tank, which is 4 ft in diameter, is filled with water and is spun around its vertical centroidal axis at a rate of 10 rad/s. An open piezometer is connected to the tank as shown so that it is also rotating with the tank. For these conditions, what is the pressure at the center of the bottom of the tank? Provide your answer in psi.
A density fluid p has filled through a tank of diameter, D at a constant rate of v. The bottom of the tank has a feature of a hole with diameter of d. What is the liquid's steady-state height, h, in the tank?
Fluid mechanics
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to Patm H 424 Hg:
Solve the given
17. At 32 deg. celcius and 308 KPa absolute, the specific weight of a certain gas is 13.7 N/m^3. What is the gas constant of this gas? * 750 J/kg -K 730 J/kg -K 723 J/kg -K 713 J/kg -K 18. A cylindrical tank 0. 80 m in diameter and 0.90 m high is filled with a liquid. The tank and the liquid weighed 420 kg. The weight of the empty tank is 40 Kg. What is the unit weight of the liquid in KN/m^3? * 6.24 KN/m^3 7.24 KN/m^3 8.24 KN/m^3 9.25 KN/m^3
What is the mass M that must be suspended at the left to hold the system in equilibrium in the position shown? Please solve this problem please. With FBD and solutions PLEASE.
Refer to the picture below to solve the following problems
The water tank has a diameter of 750mm , a height of 1750mm to which the Initial height of water was 5 cm. If water was to be filled 90% of height and the water meter initial reading is 2000L, a. what is the final reading of the water in L b. Find the mass of water tank if its initial weight is 45 kg
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.