Given the following data: A. Loose Unit Weight Determination Fine Aggregate a. Weight of measure, g. 250.00 b. Weight of measure + sample, g. 8,750.00 c. Weight of sample, g. (b)- (a) d. Volume of measure, cm e. Unit weight, g/cm 1.016 Determine the height in cm of bucket if V=3.1416(22.4cm)*(height)/4 Continues computation and write your answer in 2 decimal places

Given the following data: A. Loose Unit Weight Determination Fine Aggregate a. Weight of measure, g. 250.00 b. Weight of measure + sample, g. 8,750.00 c. Weight of sample, g. (b)- (a) d. Volume of measure, cm e. Unit weight, g/cm 1.016 Determine the height in cm of bucket if V=3.1416(22.4cm)*(height)/4 Continues computation and write your answer in 2 decimal places

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter14: Computational Engineering Tools Electronic Spreadsheets

Section: Chapter Questions

Problem 20P

See similar textbooks

Similar questions

100 90 80 70 60 50 40 30 20 10 0.5 0.05 Grain size (mm)-log scale From the graph D60 = 0.997 mm; D30 = 0.39 mm; D10 = 0.14 mm. b. Calculate the uniformity coefficient, Cu. (Enter your answer to three significant figures.) Cu = c. Calculate the coefficient of gradation, Cc. (Enter your answer to three significant figures.) C. 2. Percent passing
Q:01 Find only stiffness coefficients matrix * L I B L 21 C L I L=Last two digits of your Reg# No x0.1 (meter)
Show complete solutions pls. Values: X= 646 Y= 46 A= 8 B= 7 C= 8
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa) with a cross-sectional area of A₁ = 280 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂= 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. L₁ A (1) a SO P C C b (2) D L2
Activity 3. Solve the following word problems and present your solution. 1. A surveyor's steel tape measure is calibrated at 65°F. a reading of 200 ft is found when the tape measure is used to determine the width of a building lot when the temperature is 10°F. How great an error does the temperature difference introduce? The coefficient of linear expansion steel is 6.7 x 10-6/°F.
pls compute the given. pls include complete solution.
SOM 7.1 Show your complete/correct solution. ( I need detailed solution since there is given answer.) Given answer: Pz = 160 kips Py = 80.005 kips
Hook's Law Worksheet m(g) x (тт) 1 20 9. 2 30 21 40 32 4 50 44 5 60 54 70 67 7 90 92 8. 110 115 9 130 138 10 150 161 11 200 226 3. 6.
Determine the value of Rb. a. 78.5 lb b.578 lb c. 785 lb d. 875 lb
values A,B,C A = 10 B = 20 C = 50
Opening (mm) 4.75 2.00 0.85 Sieve No. Mas Retained (grams) 4 0.0 21.6 10 20 49.5 102.6 40 0.425 60 0.250 89.1 100 0.15 95.6 200 0.075 60.4 Pan 31.2 1. Determine the percent finer for each sieve and plot the grain size distribution curve. 2. Determine Die, D30, and D6o from the grain- size distribution.
Samples of sizen=5 are taken from a manufacturing process every hour. A particular quality characteristic, which is normally distributed, is measured, and X-ba and R calculated for each sample. After 25 samples, we have the following sums: the sum of X-bar values =662.5 the sum of R values=9.0 a) Find the control limits of the X-bar and R-charts. b) Assume both Charts exhibit "in control " behavior. If process specifications are 26.40 plus or minus 0.30, estimate the fraction nonconforming. c)If the mean of the process were adjusted to exactly 26.40, what would be the new fraction non-conforming?