Given following data, calculate a. Volume of measure b. Bulk density c. Absorption d. Void content I. DATA TO BE GATHERED:Calibration:1. Mass of the measure plus plate, kg (Mm+p)11.69 kg2. Mass of the measure plus plate and water, kg (Mmep+w) = 15.47 kg3.78 kg= 28°3. Mass of the water to fill the measure, kg (Mw)4. Temperature of water in the measure, °C (Tw)Bulk Density:1. Mass of aggregate plus measure, kg (G)14.54 kg= 9.14 kg0.00379 m32. Mass of the measure, kg (T)3. Volume of the measure, m (V)IIIIII

Factor for the measure F=DW-M=1Vwhere D=Density of water for the measured temperature in…

I. DATA TO BE GATHERED: Calibration: 1. Mass of the measure plus plate, kg (Mm+p) = 11.69 kg 15.47 kg 3.78 kg = 28° 2. Mass of the measure plus plate and water, kg (Mm+p+w) 3. Mass of the water to fill the measure, kg (Mw) 4. Temperature of water in the measure, °C (Tw) Bulk Density: 1. Mass of aggregate plus measure, kg (G) 2. Mass of the measure, kg (T) 14.54 kg 9.14 kg 0.00379 m³ %3D 3. Volume of the measure, m³ (V) %3! %3D

I. DATA TO BE GATHERED: Calibration: 1. Mass of the measure plus plate, kg (Mm+p) = 11.69 kg 15.47 kg 3.78 kg = 28° 2. Mass of the measure plus plate and water, kg (Mm+p+w) 3. Mass of the water to fill the measure, kg (Mw) 4. Temperature of water in the measure, °C (Tw) Bulk Density: 1. Mass of aggregate plus measure, kg (G) 2. Mass of the measure, kg (T) 14.54 kg 9.14 kg 0.00379 m³ %3D 3. Volume of the measure, m³ (V) %3! %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the following data: B. Compact Unit Weight Determination Fine Aggregate a. Weight of measure, g. 300.00 b. Weight of measure + sample, g. 8,820.00 c. Weight of sample, g. (b) – (a) d. Volume of measure, cm e. Unit weight, g/cm 1.019 Determine the diameter in cm of the bucket if V=3.1416(d) (21.23)/4. Continues computation and write your answer in 2 decimal places O 22.39 O 32.29 O 23.92 O None of the abovel O 23.29
The following table shows the results obtained from laboratory tests done on samples of aggregates. Weight of Aggregates + BSG for Metal Metal Measure % ABS % MC SSD Measure Inside Diameter = 6 inches Height = 12 inches Empty weight = 8.62 kg 30.39 kg 2.67 3.69 9.24 1. Calculate the Dry Rodded Unit Weight of Aggregates in kg/m³. 2. Calculate the % Voids in 1 m³ of aggregates.
5.24 Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B 40% Aggregate C 25% For each aggregate, the percent passing a set of five sieves is shown in the fol- lowing table: Sieve Size (mm) % Passing Agg. A % Passing Agg. B % Passing Agg. C 9.5 85 50 40 4.75 70 35 30 0.6 35 20 0.3 25 13 1 0.15 17 7 Determine the percent passing each sieve for the blended aggregate.
Using 0.45 power method to draw and compare between the aggregate gradations below. Sieve (mm) 25 19 12.5 9.5 Gradation I 100 95 87 Gradation II 100 95 70 4.75 2.36 1.18 0.6 0.3 0.15 0.075 30 23 17 12 7 77 56 42 38 57 25 17 12 10 9 8
Notice: This is only for REVIEW PURPOSES, this is NOT GRADED. A 100 block is in equilibrium. What is the magnitude of the frictional force between this block and the surface? Given: Us = 0.3 2 lb Options: A. 0 lb B. 1 lb C. 2 lb D. 3 lb E. Othe answer
From Data What is Material Ultimate Strength In Mpa. 1 Material Aluminum 2 Form Cylinder ve 3 Diameter 12.8 mm 4 Gauge Length 5 Tensile Testing 50.8 mm To Failure 7 8 Load (N) Length (mm) 9 0 50.8 10 7330 50.851 11 15100 50.902 12 23100 50.952 13 30400 51.003 14 34400 51.054 15 38400 51.308 16 41300 51.816 17 44800 52.832 18 46200 53.848 19 47300 54.864 20 47500 55.88 21 46100 56.896 22 44800 57.658 23 42600 58.42 24 36400 59.182 25
Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine when in operation and provide a stress analysis on the piston .use a factor of safety of 5. Assume outside temperature (bottom plate) is -233 degC and an internal PC board (top plate) is 85 degC ? wwbewn Figure 1.1 show measurement to help you to find the volume / Area Ø1.50 Ø8 Ø 10 - Show your calculations and the analysis and find the applied load on it
4. MECHANICAL SEPARATION A sieve analysis gives the following results: Sieve size (mm) Wt. retained (g) 1.000 0 0.500 64 0.250 0.125 0.063 324 240 48 24 Through 0.063 Plot a cumulative size analysis and a size-distribution analysis, and estimate the weights, per 1000 kg of powder, which would lie in the size ranges 0.150 to 0.200 mm and 0.250 to 0.350 mm.
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket = 0.2 cuft Weight of empty bucket is 18.2 lb Weight of bucket filled with dry rodded coarse aggregate = 58.6 lb Calculate the dry-rodded unit weight in lb/ft^3 (one decimal only). Input magnitude only.
(C).Workout flakiness & elongation index from the following Flakiness Index Weights of aggregates passing through corresponding slot=w2=200 grams Weight of aggregates retained on a particular sieve =w1=700 grams Workout flakiness index? Elongation Index Weights of aggregates Retained on gauge length =w2=190 grams Weight of aggregates retained on a particular sieve =w1=540 grams Workout elongation index? Are these flakiness & elongation index within permissible range? Also mention bad effects of greater amount of flaky & elongated particles.
Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to ASTM C 33, the sample is acceptable or not? BS Total mass of sample 4 80 g Sieve size 10 mm 5 mm 2.36 mm 1.18 mm 600 μm 300 μm 150 μm €150μm ASTM in 4 8 16 30 50 100 <-100 Mass retained O 80 40 80 110 68 61
F1 = 603N F2 = 818 N Show a clean and organized solution please.