Given an ideal diesel cycle, fill in the table and calculate the work in one cycle and the efficency of the cycle P [bar]0.85V [m³]T (°K)333State1234 massof airin eachсуслеm: 0.5 kgairP₁ = 0.85 barT₁ = 333 KC=12copressionratio /kJkg. °Kc=1.003-PC=0.711-kJkg. °KkJkg. °KR = 0.287Qin = 387 kJ

Answered: Image /qna-images/answer/672f212c-94d7-4970-a40e-3c8a882a5fbf.jpg

Answered: Given an ideal diesel cycle, fill in…

Engineering

Mechanical Engineering

Given an ideal diesel cycle, fill in the table and calculate the work in one cycle and the efficency of the cycle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Give an Example of a problem on Actual Reheat rankine cycle with complete solution and compare it…

Q: Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an…

Q: The working principle of a diesel engine is the Carnot cycle Ture O False O

A: To state whether TRUE or FALSE.

Q: Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an…

Q: 1.At the beginning of isentropic compression in a diesel standard cycle, the pressure and…

Q: Why is cp not used in the Stirling cycle analysis?

A: Find: Why cp is not used in Stirling cycle? Solution: Stirling cycle: Stirling cycle is a…

Q: A gas turbine power plant has specific heat ration of 0.72 with compression ratio of 0.12 Calculate…

A: Given: Specific heat ratio for gar turbine power plant→γ=0.72 And compression ratio →r=0.12 Because…

Q: Please use appropriate format for answering word problem: An ideal cold air standard Diesel cycle…

Q: Consider an ideal Brayton cycle operating on air. The inlet to the compressor is 300 K, 100 kPa. The…

Q: If a Diesel cycle and Otto cycle have the same initial conditions, the same compression ratio, and…

A: When the piston is at the bottom of its stroke ('bottom dead centre', tdc), the compression…

Q: Consider an ideal gas-turbine cycle with the following details in Table 1. Table 1 No. of stages at…

Q: Perform detailed analysis (Draw the cycle schematic and T-s diagram; find the turbine output work,…

Q: An air-standard Spark Ignition cycle has a compression ratio of 10.2. Air is at 3000 0R at the end…

A: Given data as per the question compression ratio =10.2 As the inlet condition of the air is not…

Q: 4.) An ideal Brayton Cycle has air at 100 kPa and 25C entering the compressor. After the heating…

Q: Show the process on TS- diagram.

A: Given: A reversed Carnot cycle To define: Modifications require to act as a Theoretical vapor…

Q: an ideal Otto cycle with a compression ratio of 8. Find the efficiency of the cycle with the high…

A: The pattern of the Otto motor is known as the Otto cycle. It is the one of most normal thermodynamic…

Q: The air standard efficiency of an Otto cycle is 50 % and the ratio of specific heat is 1.5, then its…

Q: Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an…

Q: A gas turbine power plant operating on Brayton cycle shown in figure. The air enters the compressor…

A: given; inlet compressor temperature(T1)=300kexit compressor temperature(T2)=700kturbine inlet…

Q: Prove that there is an increase in efficiency between a Simple Rankine Cycle and a Reheat Rankine…

Q: A gas turbine power plant operating on Brayton cycle shown in figure. The air enters the compressor…

A: For the Brayton cycle, r = compression ratio of the compressor = 7 T1 = 300 oCT2 = 700 oC P3 = 600…

Q: An ideal air-standard diesel cycle with inlet conditions: 21.11˚C and 14.7 psia, 700 Btu/lbm heat…

A: Dear Student, As per the Bartleby guidelines we are supposed to answer only first 3 subparts .Kindly…

Q: and pressure ratio of the compressor and turbine is 8. If the ar are 1.0 bar and 300 K. find the…

A: Given:ηc=0.86ηT=0.90T3=1200 KT1=300 KP1=1 barrP=8γ=1.4

Q: A Carnot cycle has been chosen as a candidate for the ideal vapor power cycle. The pump inlet is a…

A: The minimum pump work will be about 10 kJ/kg.

Q: What are the two benefits of adding a reheater to a Rankine cycle?

A: Power plants that employ coal or nuclear energy frequently use the Rankine cycle, also known as…

Q: We wish to model a gasoline engine for an automotive application with the ideal Otto cycle. The…

Q: = 300 K and T A gas turbine plant operates on the Brayton cycle between T 1073 K. Find the maximum…

Q: 10m 10m 4. An ideal Brayton cycle has a low and high pressure of 14.7 psia and 100 psia. The…

Q: An air-powered Otto cycle has a compression ratio of 8. Since the lowest and highest temperatures of…

Q: Analyse the Diesel and Otto cycle with PV diagrams and its efficiencies.

A: Draw the PV diagram of Diesel and Otto cycle as shown below,

Q: Perform detailed analysis (Draw the cycle schematic and T-s diagram; find the turbine output work,…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: ・An ideal Diesel cycle receives air at 105 kPa and 315k for isentropic compression. The cycle has a…

A: Given that: For the diesel cycle, P1 = 105 kPa, T1 = 315 K Cut off ratio = 2, Compression ratio = 17…

Q: How is heat added and rejected in an actual Otto cycle engine? Explain well and don't copy please.…

A: In ideal Otto cycle heat addition and heat rejection takes place at constant volume.

Q: n an air standard diesel cycle, compression starts at 100kPaa and 300K. The compression ratio is…

A: To determine the efficiency of diesel cycle.

Q: What is the ideal Otto-cycle efficiency for a 8:1 compression ratio, and how does it compare to the…

A: Given :The flame temperature is The compression ratio is

Q: Solve the Problem. Submit your solution with the problem with the submission area. Consider an ideal…

Q: Rankine cycle list few reasons why thermal efficiency was so low

A: For comparison purpose we will compare rankine cycle with ideal carnot cycle which has zero…

Q: Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the cycle…

Question

Given an ideal diesel cycle, fill in the table and calculate the work in one cycle and the efficency of the cycle

P [bar]
0.85
V [m³]
T (°K)
333
State
1
2
3
4

mass
of air
in each
сусле
m
: 0.5 kg
air
P₁ = 0.85 bar
T₁ = 333 K
C=12
copression
ratio /
kJ
kg. °K
c=1.003-
P
C=0.711-
kJ
kg. °K
kJ
kg. °K
R = 0.287
Qin = 387 kJ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Explain why constant pressure is applied during heat addition process in an ideal Diesel cycle.
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
An idealcold air-standard Brayton cycle produces some quantity of power. Air with a mass flow rate of 6 kg/s enters the compressor at 100 kPa, 300 K.It is also known that the compressor has a pressure ratio of 10 and the turbine inlet temperature is 1400 K.If k = 1.4for the working fluid, determine the thermal efficiency, the ratio of back work, and the net power for the cycle in kW.
Calculate the thermal efficiency of the heat engine working on the diesel cycle takes in air at 1 bar. 20 °C and a compression ratio 12 and the highest temperature during the cycle was 1100 c
An ideal diesel cycle powered by air has a compression ratio of 20. At the beginning of the compression process, the pressure of the air is 100 kPa, the temperature is 20 °C and the highest temperature of the cycle must not exceed 2250 K. Show the cycle in the P-v diagram.Then calculate: a) The heat entering and leaving the cycle, the thermal efficiency of the cycle, b) the average effective pressure of the cycle. Assume that specific heat is constant at room temperature constant at temperature. k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK
How can we increase the efficiency of the Rankine cycle? Discuss one method where the changes to be done in the ideal Rankine cycle for the sake of efficiency enhancement. Show the changes in schematic and T-S diagram.
In a regenerative gas turbine cycle, the pressure ratio, maximum temp and min temp is 4.5, 900 K and 290 K, the cycle efficiency will be equal to
An ideal Brayton Cycle has air at 100 kPa and 25C entering the compressor. After the heating process, the air has a max temperature of 870C, and the pressure is 10 times of the initial pressure. Draw the PV and TS diagrams, find the QA, WT, Wc, Wnet and efficiency.
Determine percent change in efficiency of Otto cycle when Compression ratio is changed to 12 from 8.
A simple Rankine cycle works betw een pressures 57 bar and 10 Kpa, the initial condition of steam being dry saturated. Calculate the cycle efficiency, work ratio and specific steam consumption.
1.) A Steam power plant operates using the ideal Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400C then after expanding, it condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
An ideal Diesel operates with a compression ratio of 14. The compression process begins with air at70oF and 15 psia. The maximum temperature in the cycle is 3540oF. The cut-off ratio.a. 2.09 b. 6.09 c. 4.09 d. 7.09 Also Determine the thermal efficiency. a. 0.44 b. 0.55 c. 0.66 d. 0.77