.) An Engine operating using the ideal Otto Cycle receives air at 15 psiaand 75 F, then compresses it to 1.76. The total heat added duringheat addition process is 352 Draw the PV and TS diagrams. SolveBtulbfor: the remaining temperatures, QR, Wnet, efficiency and how manylb of air is required if the engine is rated 500hp?

Answered: Image /qna-images/answer/ec4c0a61-0381-4670-889a-5b26a1d1aa77.jpg

An Engine operating using the ideal Otto Cycle receives air at 15 psia and 75 F, then compresses it to 1.76. The total heat added during heat addition process is 352 Btu. Draw the PV and TS diagrams. Solve lb for: the remaining temperatures, QR, Wnet, efficiency and how many lb of air is required if the engine is rated 500hp?

An Engine operating using the ideal Otto Cycle receives air at 15 psia and 75 F, then compresses it to 1.76. The total heat added during heat addition process is 352 Btu. Draw the PV and TS diagrams. Solve lb for: the remaining temperatures, QR, Wnet, efficiency and how many lb of air is required if the engine is rated 500hp?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3 For an ideal diesel cycle using air, temprature and pressure at the start of compression are 15°C and 1.01bar. The compression ratio is 16 and heat addition is 400kj/kg. Draw PV daigram of the cycle and drive the relationship for thermal efficiency. Calculate maximum temprature and thermal efficiency of the cycle.
in a regenerative cycle the inlet conditions are 40 bar and 400°C. Steam is Bleed at 10 bars in regenerative heating. The exit pressure is 0,8 bars. Neglecting Pump work; determine the efficiency of the cycle
Q3/A cold air standard Otto cycle has a compression ratio of 8. The cylinder state at the end of the expansion process is T500 K and P=620 kPa. The heat rejection per unit mass is 163 kJ/kg. Determine the following: Network per unit mass of air, b) Thermal pressure. efficiency. c) Mean effective
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
2.) A Steam power plant operates using the actual Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400C then after an irreversible adiabatic process, it exits the turbine with a dryness of 0.90. It then condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
In a reheat cycle steam at 15 MPa, 540 degrees Celsius enters the engine and expands to 1.95 MPa. At this point the steam is withdrawn and passes through a reheater. It reenters the engine at 540 degrees Celsius. Expansions now occur to the condenser pressure of 0.0035 MPa. Find the efficiency.
An ideal Brayton Cycle has air at 100 kPa and 25C entering the compressor. After the heating process, the air has a max temperature of 870C, and the pressure is 10 times of the initial pressure. Draw the PV and TS diagrams, find the QA, WT, Wc, Wnet and efficiency.
3- Air enters the compressor of a gas turbine at 120 kPa, 310 K. The air compressed to 1100 kPa, the turbine inlet temperature is 1460 K and the expansion occurs in two stages, with reheat to 1420 K between the stages at a pressure of 300 kPa. The compressor efficiency is 85 %. The net power developed is 2.2 MW. sketch T -S diagram then Determine: The thermal efficiency of the cycle. Qin Qin The back work ratio. Combustor Reheat combustor Turbine Turbine stage 1 stage 2 cycle Compressor
Determine percent change in efficiency of Otto cycle when Compression ratio is changed to 12 from 8.
1.) A Steam power plant operates using the ideal Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400C then after expanding, it condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
Q.6 A vapor compression cycle uses R134a as the refrigerant . The vapor condenses at 40 degrees * C and is subcooled to 35 degrees * C before entering the expansion valve . The evaporating temperature is - 5 degrees * C . The vapor leaving the evaporator is superheated to 5 degrees * C at entry to the compressor . The heat absorption rate is 13 kW and the compression process is isentropic . Calculate (i) the refrigerant flow rate, (ii ) the work input , and ( iii ) the COP . Answers: () 0.0837kg * s ^ - 1 , (ii) 2.63 kW , (iii) 4.95
Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an ideal cycle. Extractions for feedwater heating occurs at 3 MPa and again at 1.4 MPa, with the remaining steam expanding to 0.0065 MPа. What is the engine work in KW