Solve the questions in the screenshot on MIPS; Give the values of the following eight control signals for the MIPS instructionslti $to, $s1, 4ALU Source, Reg Write, Mem_to_Reg, Reg Dest, MemRead, MemWrite, Branch, Jump

```mips # Solve the questions in the screenshot on MIPS # For the instruction: slti $t0, $s1, 4 #…

Answered: Give the values of the following eight…

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter2: Introduction To Systems Architecture

Section: Chapter Questions

Problem 2VE: A(n) __________ is a storage location implemented in the CPU.

See similar textbooks

Similar questions

(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
The program counter (PC) contains the address of the next instruction -pair to be fetched from memory? a. True O b. false
destination register after each of the following instructions executes in sequence, given that CL, DX, and AL are initialized to 3, 1001111010111100, and 01010111 respectively? Leave your answer in binary form for this question rol dx, cl
Find out the control signal for the following instructions. The complete datapath and control signals given as following:
What is the result of each instruction of the following program and its effect on flag register? Instruction Result MVI A,DE MVI C,10 SUI 22 MOV D.A SUB C DCR D RST5 Flags
The following instruction is used for: GPIO PORTA_DIR_R 6= -0x20; Select one: a. direction PAS output O b. direction PFS input c. direction PA4 input d. direction PAS input e. direction PFS output
For the following instructions show which are allowed and not allowed then write the reasons: -SUB SS, DS -ADD [BX],[300H] -SUB 08, AL -INC [BX+5] -ADC CX, DL
timescale ins / lps module flipflop (Q, D, clk): input D, clk: output Q; always@ (posedge clk) begin Q<=D; end endmodule Which of the following is true for the above verilog code? Your answer: O A register must be added to the code for the input. O Output is equal to the inverse of the input. Initial block can also be used instead of always block. A register must be added to the code for the output. Clear answer
The instruction that moves each bit to the right, copies the lowest bit into the Carry flag, and copies the Carry flag into the highest bit position is the one that does this.
5. Load the register (CL) from the memory location [050OH] then subtract the content of this register from the accumulator (AL). Correct the result as a (BCD) numbers. Let [0500H] 12H & AL 3FH %3D
26. Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET
4. Find the value of the accumulator register (AL) which initially stores the hexadecimal value OXD1 and the carry flag (CF) after the following operations. Assume that the operations are to be applied to this original value separately (not one after another) and assume that CF is cleared before all operations. a. SAL AL, 2 AL CF b. SHR AL, 3 AL CF C. ROL AL, 2 AX CF d. RCR AL, 3 AX CF

SEE MORE QUESTIONS

Recommended textbooks for you

Systems Architecture

Computer Science

ISBN:

9781305080195

Author:

Stephen D. Burd

Publisher:

Cengage Learning

Systems Architecture

Computer Science

ISBN:

9781305080195

Author:

Stephen D. Burd

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Give the values of the following eight control signals for the MIPS instruction slti $to, $s1, 4 ALU Source, Reg Write, Mem_to_Reg, Reg Dest, MemRead, MemWrite, Branch, Jump