Give me the solution of these with these answers:2. ?? = 107.725 MPa3. the shear stress in the anchorbolts. Ans: ? = 91.44 Mpa 3. theshearstressintheanchorbolts.40°Pin(a)(b) A steel strut S serving as a brace for aboat hoist transmits a compressive forceP =54kN to the deck of a pier. Thestrut hasa hollow square crosssectionwith a wall thickness t12mm and theanglehorizontal is 40°. A pin through the struttransmits the compressive force from thestrut to two gussets G that are welded toebetweenthestrutandthethe base plate B. Four anchor bolts fastenthe base plate to the deck. The diameterof the pin is dthe gussets isof the base plate is Bt =8diameter of the anchor bolts is bolt d =18 mm, the thickness of15 mm, the thicknesstGmm, and the12mm. Determine the following stresses:2.the bearingstressbetweentheanchor boltsandthe base plate,

Answered: Image /qna-images/answer/ff9b490c-507b-48ad-b665-5ac5403dbdc5.jpg

Answered: Give me the solution of these with…

Give me the solution of these with these answers: 2. ?? = 107.725 MPa 3. the shear stress in the anchor bolts. Ans: ? = 91.44 Mpa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The state of stress at a point is shown on the element. Enter your answers numerically separated by commas. ΥΠ ΑΣφ vec max min = ksi Submit Request Answer Figure Part B Determine the absolute maximum shear stress. ΑΣφ ve 2.5 ksi ksi Fabs mar= 4 ksi Submit Request Answer 5 ksi Provide Feedback 圓

Part 2,3,4
I need to solve the question in the strength materials
3. For the given state of stress, determine the principal planes, the principal stresses, the max shear stress. You must use Mohr's Circle. 20 MPa 32 MPa 55 MPa
The couple M=1.1 kN-m acts in a vertical plane and is applied to a beam oriented as shown. Determine the stress at point A 10 mm 40 mm The stress at point A is ( 10 mm 40 mm -10 mm 1,-1.894 x 10 mm 1,-0.614 x 10 mm +0.800 x 10 mm MPa.
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Consider the state of plane stress shown. (Hint: Consider both in-plane and out-of-plane shearing stresses.) 7 ksi Determine the maximum shearing stress when ox- 18 ksi and ay = 8 ksl. The maximum shearing stress is ksi.
The stresses acting on an element are dx = 745 psi, ay = 615 psi, and Txy = 430 psi. (Consider only the in-plane stresses the stresses in the x-y-plane). Oy Determine the principal stresses (in psi) and angle of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention. For maximum shear stress, enter the magnitude.) %1 = psi 0₂ = psi psi max = 8p = Show the stresses on a sketch of a properly oriented element. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen This answer has not been graded yet.
4. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown in the figure together with the given section properties. The torque of 1000 N-m is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly. Answer: TĄ = 5.57 MPa Ts = 22.0 MPa 3 m 1.5 m Ta Aluminum Steel 75 mm dia. T=1.0 kN•m Ga- 28 GN/m²? 50 mm dia G, - 83 GN/m?
THE BEAMS SHOWN IN FIGURES (a) AND (b) HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPa AND IS SUBJECTED TO A POSITIVE BENDING MOMENT Mu=140KN-m. ANSWER THE FOLLOWING.1. DRAW THE INTERNAL STRESS AND STRAIN DIAGRAM OF BEAM CONSIDERING THAT THE DEPTH OF THE STRESS BLOCK IS GREATER THAN THE THICKNESS OF THE FLANGE.