give an example of a use for a nut driver

Q: List five things that could cause premature bearing failure

A: No matter what, things are bound to break. The same holds for bearing. But it can be prevented by…

Q: What are advantages of Spring usage?

A: Spring: It is a mechanical device or object which has a ability to store the mechanical energy. The…

Q: Is a hook good on a compression spring launcher trigger mechanism

A: Given Spring triggered mechanism To find Verify hook is good for spring triggered mechanism

Q: esign of the Screw Jack. Lifting load – W, kN is 70.  Hight of lifting– H, mm is 500 Types of…

A: a screw jack is used to transfer the rotational movement into linear movement. It Uses a power screw…

Q: Design of the Toggle Jack. Lifting load – W, kN is 8 Distance between nuts– B, mm is 50 - 280…

A: Given:  Lifting load is W=8 KN number of links is n=8 length of the link L=140 mm material of the…

Q: what is the minnimum proof strength mpa for M14x2 hex bolt

A:

Q: Give an example of calculating Safety Factor of bearing.

A:

Q: of screw thread from ihe foll reasons for it. (2) (31

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: The nominal diameter of V00 bolt is diameter. If safe tensile stres of the bolt

A:

Q: , the minimum metric specification required for the bolt is

A: Given, From the given shows,  Three bolt system having, Shear yield strength,σyt=200 MPaFOS=…

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: Please name two type of locking nut, and explain how they function.

A:

Q: the minimum metric specification required for the bolt is

A: Given, Determine the minimum metric specification required for the bolt ? where, Figure shown three…

Q: When discussing axle hub nuts, Technician A says that they are never to be reused after they have…

A: Solution:

Q: State the choice of power screw that suitable to be used for an application under the following…

A: (i) To select: The power screw that suitable to be used for an application under vertical lifting.…

Q: Define the Crowned Nut and where is it used? Please define the shoulder nut and where is it used

A: Crown-Nuts. An Embed for utilization inside the end of the circular and square area. The Crown-nut…

Q: What does a worm screw pulley do and what is it used for? Explain the working system in detail.

A: The worm screw is the driving gear in the worm gear arrangement. The worm gear is the arrangement of…

Q: Clearly explain the methodology involved in determining torque, power, and efficiency of power…

A: Consider the diagram shown below for the lowering and raising the load. Here, dm: mean diameter of…

Q: Using the method of joints, de

A: first of all find out all required angle from geometry, then find reaction forces at B and C then…

Q: Advantages and disadvantages of using smaller bolts than bigger bolts

A:

Q: Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt.…

A: Technician A is not correct as the 10.9 grade bolt has more strength than 8.9 grade. Grade 10.9 is…

Q: change in spring stiffness is?

A: Given: If the wire diameter of a compressive helical springs is increased by 2%,We have to find then…

Q: sketch and explain any six work holding devices used on drillind machene with tow diagram

A: Given Drill machine To find Work piece holding device

Q: What is the cause of slipping inductile failure?

A: Causes of slipping in ductile failure are as follows

Q: stiffness (in N/m) of the required mounting pad

A: Given; A precision instrument package m= 1 kgSurface vibrating at= 60 HzIsolation is designed with…

Q: bolts required for an

A:

Q: : Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer in…

A:

Q: How mary MI4 10.9 bolts used in Vith &s Systen ?

A: ANSWER- 5 BOLTS

Q: Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt…

A: The bolt will be fatigued in both the overtighten and under-tightening cases

Q: If the service information does not provide a loosening sequence for the cylinder head bolts, what…

A: Cylinder head bolts are loosened to open the cylinder in order to work on it. A cylinder head is…

Q: ce every 2 weeks (10 working days). Lead time is 2 days. The company has deter- ned that the average…

A:

Q: what the application and uses of the motorized Nuts crusher?

A: This creation identifies with a nut organic product breaking machine. Said nut organic product…

Q: List the steps that should be followed to preciselytighten a bolt to specifications.

A: Common fasteners that join two or more pieces of work together include nuts and bolts. You will need…

Q: What is the type of bearing where the load ot carris is Perpendicular to the axia of the shaft it…

A: There are two main type of bearing : thrust bearing and radial load bearing

Q: Nuts installed on a piece of all-thread experience the following forces in service FA Fg Fc FD 3.5…

A: lets consider the screw into three segments area of all threadA=π4×0.72A=0.384in2

Q: A M16 x 2 hex-head bolt with to clamp together two 25-mm thick steel plates. a nut is used

A: GivenM16×2 hex-head boltt=25 mm

Q: Which of the following arrangements is least effective in tightening the nut? rod wrench wrench nut…

A: The Force acting in each case is F. The amount of torque produced by the force F depends upon the…

Q: Fnd size of bolt by Aocenbeag Criteria

A:

Q: If pressure or force has to be applied to mating components during assembly, then type of fit is…

A:

Q: With neat sketch explain six different bearing failures, causes and cures.

A: Bearing failures, causes and cures

Q: What is the complete specification of a nut having a stress area of 0.170 in? (standard size) that…

A: 1/2"-28UNEF-3B-LH

Q: For the mechanism below: Rolling contact

A: Given Data⇒ Problem definition⇒ Problem says determine

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.