generator operating at 50Hz delivers 1 pu power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 pu whereas before the fault, this power was 2.0pu and after the clearance of the fault, it is 1.5 pu. By the use of equal area criterion, determine the critical clearing angle.

generator operating at 50Hz delivers 1 pu power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 pu whereas before the fault, this power was 2.0pu and after the clearance of the fault, it is 1.5 pu. By the use of equal area criterion, determine the critical clearing angle.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.64P

See similar textbooks

Similar questions

In the medium and large transformers, the total copper losses should be A2 % of the rated output. (a) 0.7 to 0.9 (b) 0.5 to 2 (c) 0.2 to 0.6 (d) 0.4 to 1 In DC machines, provides the magnetic path as well as the
A generator operating at 50 Hz delivers 1 pu power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place. reducing the maximum power transferable to 0.5 pu whereas before the fault, this power was 2.0 pu and after the clearance of the fault, it is 1.5 pu. By the use of equal area criterion, determine the critical clearing angle.
Question 6 What is phase angle of voltage induced in primary and secondary windings of transformers due to mutual flux? Same Opposite Zero None of option A Moving to another question will save this response. AR e IT:7
In large transformers, the total copper losses may vary from the rated output. % of 0.8 to 1.5 0.2 to 0.6 0.5 to 1 0.4 to 1
Description In the particular case of figure below derive both the critical clearing angle and the critical clearing time. P, = Pmaz sin d Pm A1 do der Smar A generator having H = 6.R MJ/MVA is delivering power of 1.0 per unit to an infinite bus through a purely reactive network when the occurrence of a fault reduces the generator output power to zero. The maximum power that could be delivered is 2.5S per unit. When the fault is cleared, the original network conditions again exist. Determine the critical clearing angle and critical clearing time. (Roll=PQRS)
A 15 MVA, 6.6 kV, wye connected generator has X 1 = X 2 = 20%and X 0 = 10%. The neutral of the generator is groundedthrough a reactor of 5% reactance based on the generatorrating. A double line-to-ground fault occurs at terminals band c. What is the current in the ground?
(9) An unloaded generator with a pre-fault voltage 1 pu has the following sequence impedance: Zo = 0.15 pu, Z₁ = Z₂ = 0.25 pu The neutral is grounded with a reactance of 0.05 pu. The fault current in pu for a single-line to ground fault is (a) 3.75 pu (b) 4.28 pu (d) 7 25 pu
The negative sequence current of a solidly grounded generator for single line to ground fault is j 2.5 p.u. Then the current flow through the neutral during the fault is j 2.5 pu j0.75 pu j7.5 pu j0.25p.u
In single phase power factor meter there is error due to frequency and waveforms but not in three phase power factor meter, I know the reason why?? Please elaborate properly
Q3/ For the system shown in figure. The generator is supplying 1.0 pu MW power under prefault condition. When three-phase fault occur at point F. What should the value of fault reactance must be to make the critical clearing angle equal to 58.9. Sc j0.1 j0.1 10.21 BE j0.38 38 j0.21 IEgl-12 pu 10.19 F 10.19 IVI-1.00 pu j0.1 j0.1 Q4/ Figure below shows the one-line diagram
A generator feeds power to an infinite bus through a double circuit transmission line. A3 phase fault occurs at the middle point of one of the lines. The infinite bus voltage is 1 pu, the transient internal voltage of the generator is 1.1 pu and the equivalent transfer admittance during fault is 0.8 pu. The 100 MVA generator has an inertia constant of 5MJ/MVA and it was delivering 1.0 pu power prior of the fault with rotor power angle of 30 °. The system frequency is 50 Hz. The initial accelerating power (in pu) will be
the slip-rings replaced by separated segments In order to generate a bidirectional Voltage true / false