G3($) CCSI てS) GCS) Gz(S) G4 CS) HIS)

Why is the R-2R ladder DAC design better than a binary-weighted DAC design, particularly if you extend to 16 bits?

In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…

4- For an operational amplifier circuit below. Draw the input and output waveforms if Vin is sine wave with 10 mV,R₁ = 10 KM, and R₂ = 100 KM. VI R₂ www PO

4. Design a clipper circuit which limits input signals to +3V and -2V. This means that the output signal should not rise above 3V and should not fall below -2V. Assume Vs has amplitude of 5V and a frequency of 1 kHz, Verify your design by computer simulation on a computer.

In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…

Design and implement a combinational circuit that multiplies by 5 an input decimal digit represented in BCD. The output is also in BCD.

In Basic electronics lab on summing amplifier Arifa is asked to give the circuit connectionaccording to figure below to make a three input summing amplifier. She uses IC 741 as OP-AMPand two power supplies to power up the IC. According to the instruction of his teacher she usesthree input such that ?1 = 2?, ?3 = −1? & set ?2 such that the output voltage ?0 = −16.5?.   A. What is the virtual ground of OP-AMP?B. Draw the equivalent circuit of OP-AMP and then simplify it for Ideal case.C. Determine the value of ?2 from the figure above for which ?0 = −16.5?.D. If the 50KΩ feedback resistor is replaced by a capacitor of 100uF what will be the outputvoltage after 1 second. Use the value of ?2 = 5 ???(200??)?�

shows a block diagram of a process con- trol system. Determine the range of the gain K for stability. Figure K Figure Process control system. Verify using Nyquist on Matlab

Draw the output on top of the input waveforms for the circuits below. For all circuits in this question, assume that +Vout(max)= +10V and -Vout(max)= -10V .