g) Calculate the magnitude of the maximum bending stress in the beam. Enter your answer in MPa to two decimal places

Q: Why are three views used to show the object?

A: As we all now everything around us can geometrically be defined in the cartesian coordinate system.

Q: what is x in this crank slider stick diagram, and what is its realtion to p2 (the displacment) i…

A:

Q: If an object is hanged by a string, the line of action of the string will not always pass through…

A: When an object is symmetrical then line of action of string passes through the centre of gravity of…

Q: Find reaction at A.

A:

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: The weight will always act downwards at an angle of 30 upwards at an angle of 60

A:

Q: Q 3/ Give the names of the components to the parts in the vehicles According to the figures. Manual…

A: Given figure shows the schematic of the manual transmission system.

Q: The hydraulic cylinders is also known as

A: The hydraulic cylinder is a mechanical actuator which convert hydraulic energy  into the mechanical…

Q: how would you adjust the horizontal plane

A: The horizontal plane is a geometric plane that is perpendicular to the direction of gravity and…

Q: Write F if True and T if False. Lithosphere is also called Earth's crust

A: Answer: The given statement is True-F.

Q: y h с b bh .1

A:

Q: 04: Complete the secetion of the reciprocating pump (shown in figure.2) by adding the details of the…

A: Gear box in the reciprocating pump The purpose of the gearbox is to convent rotating energy to…

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: Part B - Analyzing the force-couple system on a bracket For the bracket shown below, Fi = 165 lb, F…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. please…

Q: Pls provide the sectional view below

A:

Q: If a line is inclined to VP and parallel to HP, then its front view is a/an

A: As the required plane is parallel to the horizontal plane and inclined to the vertical plane the top…

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: A STAR WHEEL ADJUSTER RETURN SPRINGS ANCHOR PLATE E ANCHOR PIN PLATE SPRING SPRING STAR WHEEL…

A: Backing plate - C Shoe - D Wheel cylinder - A

Q: The impending motion is applied when the body is Select one: O a. Just stopped Ob. Stopped Oc. Just…

A:

Q: weight vs spring different point plz

A: Weight is a force and spring is a mechanical element. The spring may be compressed or elongates but…

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure  To sketch the missing lines  And hidden lines

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: Figure 1 of 1 8 ft 6 ft 6 ft

A:

Q: Draw a FBD the tip to tail method please show steps

A:

Q: what is the ybar distance(distance from bottom edge of triangle to centroid)?    options:   40/3…

A: Given, Right-angled triangle of, Base, b=20 in Height, h=9 in

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: What is the mechanical advantage of an input piston with a diameter of 1.25" pushing fluid to move…

A: Diameter of input pushing piston, d1= 1.25" Diameter of output pushed piston, d2= 2"   To find:…

Q: Which force would have to increase to make the car accelerate? * B.

A: Force C

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.

Q: Which corners would be visible from the FRONT orthographic view of this image. Select all that…

A: Front view will be like

Q: Can someone draw grashof's mechanism: Crank-rocker Mechanism in ENGINEERING DRAWING FORMAT basing…

A: The crank-rocker mechanism,

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: The robot shown below has one prismatic and one rotary link. Draw the work space if the prismatic…

A: To solve the problem, we need to draw the workspace of the robot described. Here are the steps to…

Q: 8ェ4 2 w/

A: the value of  (4x-4)/2= (4*(-1)-4)/2= -12/2 =-6

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.