Answered: Four resistances are connected in…

Four resistances are connected in series, 5 ohms, 10 ohms, 15 ohms and 20 ohms respectively to a voltage source 100 Volts. Solve for the V1, V2, V3 and V4 using voltage divider principle,

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Related questions

Q: Problem 3. Do the following: a. Use Kirchhoff's and Ohm's laws in a step-by-step procedure to…

A: It is given that:

Q: The charge in a 4 μF capacitor charged to 100 V will be A. 4 μC C. 100 μC B. 25 µC D. 400 μC

A: Given: Capacitance of capacitor, C=4 μF. Voltage on capacitor, V=100 V.

Q: 2. Investigate the concept "supermesh", and applied this concept to obtain in the circuit of Figure…

A: The circuit is shown below with the directions of the currents indicated:

Q: 1- the potential of the point A in the network shown in Fig.1 (a) 6 V (b)7 V (c) 8 V (d)none of…

A: Given data, Circuit diagram is given as,

Q: Problem 4. With reference to the circuit shown in Figure 4, find the power absorbed by each of the…

A: We need to find the power absorbed by each of the seven elements.

Q: Q20) If the total current supplied by the battery is 2 µA, calculate the voltage across R₂ in the…

A: Given circuit: Total current supplied by the battery, I=2 μA.

Q: * Assuming vin(t)=2sin(1000ft) volts and using simplified (2nd) diode approximation, the waveforms…

Q: 500 mA V 1 100 mA 200 mA FIGURE 6-55 R₁ R₂250 Ry 3A l 50 mA

A: The question is about voltage drop across the resistances , current, finding the total resistance.

Q: Differentiate Differential Amplifiers and Operational Amplifiers. Site an example for each type of…

A: Given: Differentiate between differential amplifiers and operational amplifiers.

Q: 8. The numerical values of the voltages and currents in the interconnection seen in Fig. 1.8 are…

Q: The shockley diode in the circuit on the right has a breakover voltage, VBO(F) of 10V specified in…

A: The circuit diagram is given as

Q: 2.4-27 Find and sketch c(t) = x1()*x2 (1) for the pairs of functions illustrated in Fig. P2.4-27. A…

Q: О XC₁ = Ginen V₁ = 5 cs(bot-45⁰) cozbrad / see) L сос, 2 хс2= йог ńcz с 6X1 =3= 6х1 36 Я =5 L-450 х…

Q: 5. For the circuit in Figure 5, calculate the current i in steady state and the power factor…

Q: Multimeter-XMM3 A -817.051 PA V 22 Set... LO FIND THE SHORTED RESISTOR, IF THERE IS ONE. V(da): OV…

A: Properties of measuring instrument 1. Voltmeter A Voltmeter is used to measure the voltage across…

Q: In EELE 201 we are learning how to use a set of tools to solve for voltage and currents in linear…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: An iron cored choke coil has an equivalent resistance of 4 Q. It draws 10A from a single phase ac…

A: Given an iron core choke coil has, Equivalent resistance, R=4 Ω. Current drawn, I=10 A. Single phase…

Q: 1. Two identical zinc-carbon batteries are available. When connected in series, they supply 0.5…

A: The basic problem on battery is solved here

Q: QUESTION 6 What is this a diagram of? O NO pushbutton ONC temperature switch ONC level switch ONC…

A: Introduction: Various parts are required to configure an electrical circuit. To understand…

Q: For the signal flow graph shown below, apply the gain formula to find the following transfer…

Q: The current at resonance in a series L– C–R circuit is 100µA. If the applied voltage is 2 mV at a…

Q: Write an expression for F and simplify.

Q: Determine v. for the circuit in Fig. 1.7. 60 V 5 A 8 Ω 4 Ω 10 Ω Μ 2Ω Ex

Q: The answer given by my school, phase angle of Vo is 0 degrees. When converting from sin to cos is it…

Q: 16. The commercial efficiency of a shunt gen- erator is maximum when its variable loss equals…

A: The given problem is a shunt generator problem. The explanation is given in the next step.

Q: The measured value of a capacitor is 205.5 µF whereas its true value is 202.4 µF. The relative error…

A: Given, Measured value of capacitor, Cm=205.5 μF. True value of capacitor, Ct=202.4 μF.

Q: +6)y(1) x(1) (a) Find the characteristic polynomial, characteristic equation, characteristic roots,…

Q: jsoo 1000+j500 ј хоб 3 لد

A: No you can't do in this way because of the following reasons.

Q: Vs CH R₁ A Fig. 1. Simple resistor circuit. This is easy to solve using Ohm's law, V=IR. At any…

Q: Differentiate Differential Amplifiers and Operational Amplifiers. Site an example for each type of…

A: It is given that: Differential and operational amplifier

Q: 4. Draw a diagram for the following: 9V

A: Given, Circuit connection on breadboard is We need to draw the original circuit.

Q: Add one of the two features shown in the image below to this circuit diagram. Which I have also…

A: According to the question, in the given circuit model as shown below, We need to add one of the two…

Q: 6. For the circuit in Figure 6, calculate the average, reactive and complex power delivered by the…

A: The capacitor is an important passive component of electrical energy which is used in electrical…

Q: The complex impedance of the series load shown below at a frequency of 60Hz is OHM. 80 μF 10092

A: The given circuit is, Supply frequency, f=60 Hz.

Q: A steel har needs 2000 AT to magnetise it. The voltage required for the magnetising coil of i00…

A: Given, Magnetomotive force, MMF=2000 AT. Number of turns, N = 100 turns. Resistance, R=20 Ω.

Q: Explain LDA, STA and DAA instructions

Q: 17. The one-line diagram of a three-phase power system is as shown in Figure 3.36. The transformer…

Q: 5. a. Calculate the total capacitance of the follow capacitors connected in series: C₁ -2.5 µF, C;…

A: We need to find out equivalent capacitance for given series combination of capacitor .

Q: 3. Obtain in the circuit of Figure 3. 8 cos 2t V 452 1 H vor 3 A 1 Figure 3: Problem 3 252 1Ω + V…

Q: 9. For a 4-pole, 2-layer, d.c., lap-winding with 20 slots and one conductor per layer, the num- ber…

A: Given: Pole, P=4 2 Layers Lap winding 20 slots and one conductor per layer

Q: 3. Use superposition theorem and get the total individual currents (with directions) and voltages of…

Q: Find the equation for the load line (diode current vs diode voltage). Also, find the current and…

A: The given circuit is as shown below,

Q: Problem-7 (e)- A 4 pole, 50 Hz synchronous generator has 48 slots in which a double layer winding is…

A: Given- 4 pole, 50 Hz synchronous generator, s= 48 slots, double layer winding, Phases=2, m=6, Number…

Q: 4. Use mesh-current method or node voltage method to solve for currents is, 16, 15, and voltage Vo…

Q: 5. The charge that enters the BOX is shown in Fig. 1.5. Calculate and sketch the current flowing…

Q: 3. If R₁ 12 Ohms and R₂ = 6 Ohms, calculate 1₁. www + V₁ - ww +V₂' 4V

A: Given circuit: R1=12 Ω.R2=6 Ω. I1=I2

Q: Draw an Input-Process-Output (Conceptual Diagram) for Hybrid Solar-Wind Power Generation.

A: Hybrid Solar-Wind Power Generator It is a power generation system by using two kinds of renewable…

Q: There are three node voltages, x, y, and z, labeled in the network. Each source contributes…

Q: Please solve the number 7. Show a clear and readable solution. Super thanks!

A: We need to write the given decimal number to sign magnitude , 1' s and 2's compliment.

Q: V₁ ΤΩ ww 2 Ω 9 V 3 A V₂ 8 Ω www 4 A 10 V3 D 26 Figure (5) Use nodal analysis to determine the node…

Concept explainers

Current Division Method

The generalized current divider formula is given by the following relation below,

Question

V1b please help me with the full solution and answer thank you

1. Four resistances are connected in series, 5 ohms, 10 ohms, 15 ohms and 20 ohms respectively to
a voltage source 100 Volts.Solve for the V1, V2, V3 and V4 using voltage divider principle,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A voltage divider consists of a 3000 – ohm, a 5000 – ohm, and 10000 – ohm resistor in series and the series current is 15 mA. Find (a) the voltage drop across each resistance and (b) the total voltage.
One of the resistors in this voltage divider circuit has failed (either open or shorted). Based on the voltage readings shown at each load, comparing what each load voltage is versus what it should be, determine which resistor has failed and what type of failure it is: - 50 V R₁ wwwww 30 R₁ w... R4 Load #1 Design voltage: -9 V Actual voltage: -31.7 V Load #2 Design voltage: -18.7 V Actual voltage: -33.8 V Load #3 Design voltage: -35.3 V Actual voltage: -41.1 V
6. Three resistors A, B and C are connected in parallel and take a total current of 7.9 amperes. Resistor A takes 2.5 amperes and has a resistance of 45-ohms. Calculate the power dissipated at resistor B, if the current draws at resistor B is twice as much as much as that through resistor C.
A secondary cell having an e.m.f. of 2V and an internal resistance of 1 ohm is connected in serieswith a primary cell having an e.m.f. of 1.5V and an internal resistance of 100 ohm. The negativeterminal of each cell is connected to the positive terminal of the other cell. A voltmeter having aresistance of 50 ohm is connected to measure the terminal voltage of the cells. Calculate the voltmeterreading and the current in each cell.
2. Three resistors R1, R2 and R3 are connected in series parallel with R1 in series with parallel combination of R2 and R3. The whole combination is connected across a 120V DC source. Resistors R1, R2 and R3 takes 750 w, 250 W and 200 W, respectively. Calculate the resistance R2. Why are street lights connected in parallel and not in series, explain.
1. A 5-ohm resistance is connected in parallel with a 10-ohm resistance. Another set, a 6-ohm and an 8-ohmresistances are also connected in parallel. The two sets are connected in series. What is the total resistance?
A 5-ohm resistance is connected in parallel with a 10-ohm resistance. Another set, a 6-ohm and an 8-ohm resistances are also connected in parallel. The two sets are connected in series. What is the equivalent resistance?
I Three resistors, 1902, 5 and 140 are connected in parallel in a circuit. What is the equivalent resistance of this combination of resistors? Give your answer to 2 significant figures in Ohms.
A 20-ohm resistor is connected in parallel with a variable resistor R. The parallel combination is then connected in series with a 4-ohm resistor and connected across a 240 V source. Determine the minimum value of Rif the power of R is equal to the power taken by the 4-ohm resistor.
Find the current I in the figure below using nodal method. All resistors are in ohms.
Two resistors RA and RB are connected in series across a 120-V source. When a 30,000-ohm voltmeter is connected across RA and then across RB, the instrument deflection is 48 volts in each case. What are the ohmic values of the resistors?
What is the voltage across the 50 Ohm and 5 Ohm resistors? Using the loop hole equation, what is the voltage across the R1? What is R1?