For this prelab, all solutions were prepared exactly as described in the lab manual; all data were also collected exactly as described. Use the following data to calculate the percent by mass of ASA in the tablet: Mass of pure ASA (used for stock solutions): 230 mg Solution Absorbance 1 2 3 4 5 0.092 0.184 0.276 0.368 0.460 Mass of tablet: 430.2 mg Absorbance of tablet: 0.162 %(by mass) of ASA in tablet:

For this prelab, all solutions were prepared exactly as described in the lab manual; all data were also collected exactly as described. Use the following data to calculate the percent by mass of ASA in the tablet: Mass of pure ASA (used for stock solutions): 230 mg Solution Absorbance 1 2 3 4 5 0.092 0.184 0.276 0.368 0.460 Mass of tablet: 430.2 mg Absorbance of tablet: 0.162 %(by mass) of ASA in tablet:

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter9: Atomic Absorption And Atomic Fluorescence Spectrometry

Section: Chapter Questions

Problem 9.16QAP

See similar textbooks

Similar questions

3. The lead in a swab sample, lead standards, together with a blank were made up in 5.00 mL volumetric flasks using 0.2 % HNO3. 20 μL aliquots of these solutions were injected into the spectrophotometer and the absorbance measured at 217 nm. The following results were obtained. lead / ppb Absorbance 0 0.0591 10.00 0.0858 50.00 0.1926 100.0 0.3260 150.0 0.4594 200.0 0.5929 Swab sample 0.3700 (a) Determine the amount of lead in the swab sample in μg.
A 10.00 g sample containing an analyte was transferred to a 250 mL volumetric flask and diluted to volume. When a 10.00 mL aliquot of the resulting solution was diluted to 25.00 mL it was found to give a signal of 0.235 (arbitrary units). A second 10.00 mL aliquot was spiked with 10.00 mL of a 1.00 ppm standard solution of the analyte and diluted to 25.00 mL. The signal for the spiked sample was found to be 0.502. Calculate the weight percent of analyte in the original sample.
During your experiment, you measure the absorbance of a sample to be 1.362. You have to convert thisabsorbance to methylene blue concentration (in ppm) using the absorbance measurements of two standardsolutions of known concentration:5 ppm: Absorbance 0.55510 ppm: Absorbance 1.211What is, in ppm, the concentration of your sample? Report using 3 decimal figures. Your answer must becorrect to 0.02 ppm
A 10.00-g sample containing an analyte was transferred to a 250-mL volumetric flask and diluted to volume. When a 10.00-mL aliquot of the resulting solution was diluted to 25.00 mL it was found to give a signal of o.235 (arbitrary units). A second 10.00-mL aliquot was spiked with 10.00 mL of a 1.00- ppm standard solution of the analyte and diluted to 25.0o mL. The signal for the spiked sample was found to be o.502. Calculate the weight percent of analyte in the original sample.
The validation process comprises four main steps that are : hardware validation, software validation, method validation and system suitability. To evaluate a spectrophotometer’s accuracy by measuring absorbance, a solution of 60.06 mg/L K2Cr2O7 in 0.0050M H2SO4 was carefully prepared together with a 0.0050 M H2SO4 as a reagent blank. If the spectrometer’s signal is properly calibrated, it has been reported that this solution should provide an absorbance of 0.640 +- 0.010 at wavelength 350 nm. Which one of the validations mentioned above had been involved in this process? Explain your choice
A student prepared four standard solutions of (NH4)2Fe(SO4)2 and measured their absorbance at 505 nm. She created a calibration plot with the best-fit line of y = 9372 x + 0.0539. She measured the absorbance of her diluted unknown sample solution as (4.69x10^-1) nm. If she prepared her diluted sample solution by diluting 10.00 mL of the original solution to a total volume of 50.00 mL with deionized water, what is the concentration of Fe2+ in her original solution? Answer in units of M. Note: Your answer is assumed to be reduced to the highest power possible.
What absorbance value corresponds to 40.0% T? A = 0.398 A 0.0109 M solution of a certain analyte exhibits 40.0% T at a wavelength of 280 nm. What will the percent transmittance be for a 0.0283 M solution of the same analyte? Assume the pathlengths for each measurement are equal. %T = of
To quantify the Cadmium content in a water sample, 5 aliquots of 10 mL were taken, adding to each one of them a volume of a standard solution of Cd (2 mg / mL); after the addition the final volume for all solutions was 50 mL. The absorbance reading was taken in an Atomic Absorption spectrophotometer, the data recorded were: Aliquot 1 2 3 4 5 Cd solution (mL) 0 1 2 3 4 Absorbance 0.163 0.240 0.319 0.402 0.478 Calculate the ppm of Cd.
For the determination of Fe3 +, 25 mL of sample taken from sea water is diluted to 100 mL and a quantity of the obtained solution is taken and Fe3 + is determined by atomic absorption spectrophotometer. The absorbance values of the standard and sample solutions are below, and calculate the Fe3 + concentration in sea water in mg / L by drawing the relevant graph.Solution Absorbance1 mg / L Fe3 + 0.04095 mg / L Fe3 + 0.205110 mg / L Fe3 + 0.411615 mg / L Fe3 + 0.620820 mg / L Fe3 + 0.8222Sample Solution 0.5155
The determination of iron in wines was carried out by atomic absorption spectrophotometry, using the standard addition method. To do this, 10 mL of wine were placed in five 50 mL volumetric flasks; then 0, 5, 10, 15 and 20 mL of a 10 ppm iron standard solution were added to each of them. Next, they were gauged with distilled water and the absorbance was measured, obtaining the values of 0.040, 0.062, 0.081, 0.102 and 0.125 respectively. Calculate the regression parameters and obtain the iron concentration in the wine, in µg / mL.
What absorbance value corresponds to 47.4% T? A = 0.323 A 0.0141 M solution of a certain analyte exhibits 47.4% T at a wavelength of 280 nm. What will the percent transmittance be for a 0.0279 M solution of the same analyte? Assume the pathlengths for each measurement are equal. %T = Incorrect %
an absorbance of a solution with a pathlength of 1.00 cm is 0.544 and concentration is 1.40x10^ ^ -3 M , what is its molar absorptivity?