For the slab shown in the figure, Fy = 420 Mpa, Col. Dimensions = 400 x 400 mm, check slab thickness at exterior panel for deflection control for the following cases: 1- Flat slab without edge beam and without drop panel 2- Use edge beam only. 3- Use Drop Panel only. 4- Use edge beam and drop panel. 5- Use beams for all lines with am = 0.5. 6- Use beams for all lines with am = 1.5. 7- Use beams for all lines with am = 2.5. Discuss the results. 7.2 m 7.2 m 7.2m 7.2 m 7.2 m 7.2 m

For the slab shown in the figure, Fy = 420 Mpa, Col. Dimensions = 400 x 400 mm, check slab thickness at exterior panel for deflection control for the following cases: 1- Flat slab without edge beam and without drop panel 2- Use edge beam only. 3- Use Drop Panel only. 4- Use edge beam and drop panel. 5- Use beams for all lines with am = 0.5. 6- Use beams for all lines with am = 1.5. 7- Use beams for all lines with am = 2.5. Discuss the results. 7.2 m 7.2 m 7.2m 7.2 m 7.2 m 7.2 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
Question Eight tensile bars with a diameter of 16mm, equally divided into Fwo layers, are developed, C=50mm Spacing between Stirrups = 150 mm center to Center and spacing be tween longitudinal bars is 80 mm if Atr=230 mm? [leastof Cs& cb], Fy = Fyt = 350 M Pa. use Fé = 25,35 and 45 MPa and assume Atr is Satis fied with ACI & BS, Find length of development vequired. > Subject: Advanced Concvete Design, %3D
Calculate the ultimate moment of the given triangular column cross-section section Mr? Paste your PEG or PNG Proof paper using menu above Na=150 kN 90 mm A = 3024 A2 =024 As2 600mm fot = 17 MPa fya = 365 MPa As1 1 60 mm 600 тm
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
12. Refer to figure 6. The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. = 20 mm a. 70.8 mm b. 75.2 mm c. 86.3 mm d. 80.5 mm e. none of the above FIGURE 6
For the composite area shown: 1. Locate the centroid in the x and y direction? 2. Find the moment of inertia about the x axis? 180mm 180mm 80mm 80mm 150mm 60mm B I U S X2 OE Shot by Hisense H12 1.
Compute for the linear weight of a 32mm diameter reinforcing bar. (Use the Unit weight of the Steel) Answer asap
EX4: A reinforced concrete beam with dimensions as shown in the Fig. below 3D24 Mpa, f,= 414 Mpa. Indicate wither the analysis by the un cracked Transformed section is correct or not.Ø32mm for steel 22kN 58KN/m 144KN 75mim T T65mm 00 h =700mm 4m 355mm
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield strength 420 MPa. If bar centroid is located 70 mm from the bottom edge of the beam and f'c = 21 MPa, calculate the design moment strength in kN-m. Write your answer with 2 decimal places only.
Design the beam shown 30KN 8m -1m use f'c= 28MPA db = 25mmø %3D Gr60 ds = 12mmø Assume d b =
Two channels having the given properties shown is placed at a distance of 300 mm to back and is properly connected by a pair of lacings as shown. 305 mm Fy=248 mpa Properties of one channel A = 5690 mm² Ix = 67.3 x 10 mm* Assume K = 1.0 -260 mm- Lucre x= 17- d = 305 mm ly 2.12 x 10 mm x 17mm CIVIL ENGINEERING - STEEL DESIGN Determine the safe axial load in kN, that the column section could carry. Unsupported height of column is 6m.