For the opamp circuit shown below tigure, calculate the followings by assuming Ag=0, 1. What is the required value of C, to locate the pole frequency at 0,5 MHz? 2. What is the required value of R2 to place the zero frequency of the system at the frequency of one-twentieth of the pole frequency? Circuit parameters / Devre Parametreleri R1=2,3 k. R2 C, R1 Ao oVout Vin 22

For the opamp circuit shown below tigure, calculate the followings by assuming Ag=0, 1. What is the required value of C, to locate the pole frequency at 0,5 MHz? 2. What is the required value of R2 to place the zero frequency of the system at the frequency of one-twentieth of the pole frequency? Circuit parameters / Devre Parametreleri R1=2,3 k. R2 C, R1 Ao oVout Vin 22

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing the corresponding circuit and by explaining your answer or presenting the solution. a. If VA-0, VB-1V, RA-RB-10kQ, R1=70kQ, R2=00 and vout-8V, which terminal (A or B) is the noninverting input? b. If VA-10, VB=0V and B is the inverting input, select RA, RB, R1, and R2 and to obtain an output voltage of 20V. c. If VA=VB=1V, R1=0, R2=∞ and Vout=1V, which terminal (A or B) is the inverting input? R2 VA RA OVout RB B VB R1
An alternative signal Vin=3sin(2π400t) is applied to the integrator circuit input designed with Op-Amp, which is given in the figure and fed with ±10V. Draw the waveform by analyzing the output voltage (Vo). Calculate the maximum and rms value of the output signal.
A appropriate op-amp circuit with a gain of +100 is required for the ultrasonic device. Create a two-stage non-inverting op-amp circuit with Av = 10 for each stage. Provide calculation procedures that complement the circuit design.
Consider Figure 65. Compute for the minimum value of R3 if R₁ = R₂= 51kohms, C₁-C₂-0.001uF and R4=115.07kohms to start the oscillation. R3= kohms +Vcc Op-amp Output sinusoidal signal -VEE S= 4,1 Figure 65 K₂
Please i need it quackly please
+Pig Given: Vimax = 8V (note: ignore E) a) analyze and draw the output waveform of Vo b) identify the type of clamper and label waveform c) indicate the cycle being analyzed
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator wilh R = 10OKOhms, C = 10UF and a sine wave inpul waveform, the output waveform is a cosine waveform. %3D ii. For an op-amp integrator with R = 100KOhms, C = 10uF and a triangular input waveform, the output waveform is a square wave. iii. For an op-amp integrator with R- 100KOhms, C =10uF and a sine wave input waveform, the output waveform is a sawtooth waveform. v. For an op-amp integrator with R10OKOhms. C lCuF and a square wave input waveform, the output waveform is a triangular waveferm.
1st question
a) For an opamp, the input bias current Ib =60uA and the input offset current lio= 10uA Find the input base currents and In b) Design an opamp circuit with the following output: Vo = - Vin/4 + 2 For the circuit given below Given :Vin-0.2V, Vsat= 12V D Identify (name) the circuit (stage 1 and 2) O Find the output voltage Vo and the current through the load 4ka 0 Find Vo if the resistor 2kn opens 10 k Stage Stage 2 Vo Vin
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww
Problem C It is desired to have a gain of 20 for frequencies up to 180 kHz. Determine the minimum unity gain frequency specification for the op amp. The gain should be within at least 98% Vsig Rin + Rf Vcc/-Vcc +12v/ -12V Vout
18 ut of estion 9 In Designing a lag compensator for the shown system, the only thing left is to determine the gain K. Take the closed loop poles ass-0.2 0.9. Determine Ke. R(s) Select one: O a. -7 O b. 1.06 O c. 2.50 O d. 1.94 Oe. 0.88 Ke $+0.5 $+0.05 lag compensator Consider the followin s(s+1) plant C()