A silicon photodiode is connected to an op-amp as indicated. Under an illuminance of 500 lux, the photocurrent Ip is 80 nA. P R = 1ΜΩ out a) Write down the values of 11, 12 and Ip. From these values, deduce the output voltage. b) Briefly describe how this circuit works. c) Will this circuit work under sunlight? The illuminance of sunlight is about 100,000 lux. You may assume the photocurrent respond linearly with incident light flux, and the op-amp is powered between 9V alkaline cell. (i.e., V+ = 9V, V at ground).

A silicon photodiode is connected to an op-amp as indicated. Under an illuminance of 500 lux, the photocurrent Ip is 80 nA. P R = 1ΜΩ out a) Write down the values of 11, 12 and Ip. From these values, deduce the output voltage. b) Briefly describe how this circuit works. c) Will this circuit work under sunlight? The illuminance of sunlight is about 100,000 lux. You may assume the photocurrent respond linearly with incident light flux, and the op-amp is powered between 9V alkaline cell. (i.e., V+ = 9V, V at ground).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Propose an electronic circuit which has an input/output waveform like the one shown in the figure below. Name the circuit and draw it. Explain what will happen if the input frequency becomes very high. Z VIN VOUT
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
A clamper circuit has 20 Vp-p. 100Hz square wave input voltage. The circuit consists of silicon diode IN4001 and 3V battery as shown in Figure 1 C. 0.1 µF D R Vi(t) 50 k2 Vo(t) 3 V Figure 1 a) Find the output voltage for all input voltages values. b) Sketch the output waveform, Vo(t).
Draw the waveform of the given clipper circuit and determine the following: a.) At 0V, what is the output voltage?b.) At +20V, what is the output voltage?c.) At -5V, what is the output voltage?
A bridge full - wave rectifier with a capacitor - input filter provides a dc output voltage of 14.5 V to a 330 ohm load. Determine the value of filter capacitor if it connected to input voltage of 12 V rms, 50 Hz. Question 7Answer a. 220 ɲf b. 208 ɲfc. 440 fd. 104 nf
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
DC to AC 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). (on for 10ms (+20V), off for 20ms, on for 10ms (-20V), off for 20ms, repeat) +20V 20ms 20ms 10ms ov 10ms -20V 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). +2-V -20V 10ms 20ms Oms 30ms 40ms
For the given circuit below, it operates on a peak- to-peak input voltage of 112.3 V, F = 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1 D2 AC Input Vsec (source) D3 .... D4 Load 4.21 4.01 7.86 7.02 ellle
(a) Figure Q2 (a) shows the image from the digital osciloscope. It shows two sine waveforms, voltage (Ch1) and current (Ch2). The value of vertical (volt/div) for Ch1, (amp/div) for Ch2, and horizontal scales (time/div) are shown in the image. Analyze the figure and determine: iv) Peak to peak value and the frequency for each waveform (voltage, Ch1 and current, Ch2) v) Phase different between two waveforms. vi) If the vertical scale (volt/div) of Chl is change to 100 V. Determine the total of division of Chl that will be displayed by the oscilloscope. Ch1 Ch2 Ch1 50V Ch2 5A M5.00ms Figure Q2 (a)
Design a simple op-amp circuit which will--- Sinusoidal wave (2V p-p, 1kHz) to amplified Square wave converter maintaining the same frequency
Determine Vo, for the circuits shown below. OPAMP is ideal.
b) For the network in figure, input is supplied by a sine wave given as V; = 10sinwt V. Diodes are selected as ideal. R = 22 ka D1. Determine i) Solve the problem and show every single analytic step in RL = 6.8 ka D the solution R2 = 22 ka ii) Draw the output waveform iii)Calculate the root mean square value of the output voltage iv)Determine the required PIV rating of the diodes. v) Draw, simulate and analyze the circuit by using PSpice