For the Op-Amp circuit shown below, v1(t) = 0.02 sin 200t V and v2(t) = 0.03 sin 200t V. Determine the output voltage v.(t). Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below. 240 kN -15V 100 kN 2.2 µF v7(t). -15V 10 kN 10 kN 15V 100 kQ 15V 6. |-15V 220 k. 3.3 µF v2(t) ko 1.

For the Op-Amp circuit shown below, v1(t) = 0.02 sin 200t V and v2(t) = 0.03 sin 200t V. Determine the output voltage v.(t). Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below. 240 kN -15V 100 kN 2.2 µF v7(t). -15V 10 kN 10 kN 15V 100 kQ 15V 6. |-15V 220 k. 3.3 µF v2(t) ko 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

D1 D V1 D4 D2 V D D Diode Model: 1N5817 R = 10k Vi= sine (0 5 100) Given the parameters above, simulate the given circuit using .tran 0 30m 0. Solve for the output peak to peak voltage across the resistor and the output frequency measured across the resistor. Output Frequency = (When computing for the frequency, use 4v as reference point) Output Voltage (pk-pk) = + R1 R D3 D
A bridge full - wave rectifier with a capacitor - input filter provides a dc output voltage of 14.5 V to a 330 ohm load. Determine the value of filter capacitor if it connected to input voltage of 12 V rms, 50 Hz. Question 7Answer a. 220 ɲf b. 208 ɲfc. 440 fd. 104 nf
Q2 In the circuit as shown below. Determine the (ripple factor) and sketch vp(out) for the filtered bridge rectifier with a load as indicated. 2 : 1 D3 D1 120Vp-p f= 50HZ + Output V1 V2 D2 D4 1uf R1=2k
What type of A/D converter would work best for video signals with a frequency content up to 5 MHz? Why? (Our subject is Principles of Electronic Communications)
3. Determine Veand Sketch output waveform for the clamper network shown. 20 V Si C Vi R 4 V- | -20 V 4. An RC filter stage (R = 42 0, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
b) An 8-bit DAC has an output voltage range of 0-2.55V.Determine its resolution in two ways. c) A 3 bit DAC has a current output. For a digital input of (110), an output current of 20 mA is produced. What will be the output current for a digital input for (010)?
1500 20V Vin RQ Vout -20V A laptop charger is connected with a load resistance R=44920 and practical PN junction diode is used as shown in Figure. Find the value of the output voltage in the negative half cycle |(in volts) if the input applied voltage is v(t)=20sin314t.
v(t) 20V Vout -20V A laptop charger is connected with a load resistance R=37942 and practical PN junction diode is used as shown in Figure. Find the value of the output voltage in the positive half cycle (in volts) if the input applied voltage is v(t)=20sin314t.
Determine the peak-to-peak ripple voltage in a brigde rectifier filter capacitor given that: Vp(rect) =10 , RL = 100 Ω, f = 500 Hz, C = 1000 μF: Select one: a. 0.25 V b. 0.10 V c. 0.20 V d. 0.35 V e. 0.15 V
An RC filter stage (R = 42 Q, C = 220 µF) is used to filter a signal of 30 V de with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
4. An RC filter stage (R = 33 , C = 120 µF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
R +Vcc -Vcc C Vout R R a. Quantify how the resistors and the capacitor influence the output voltage of the circuit, Vout. What are the upper and lower limits of Vc? b. Howlong does it take for the capacitor to be charged from minimum to maximum voltage and vice versa?