For the loading arrangement shown, the crate has a weight of 600 lb. The design requirements states that the maximum normal stress (tensile) developed on the cross section a-a should be limited to 13.9 ksi. Determine the maximum value the offset distance "x" to meet this requirement. Develop an appropriate free body diagram and determine the location of the neutral axis for section a-a.

For the loading arrangement shown, the crate has a weight of 600 lb. The design requirements states that the maximum normal stress (tensile) developed on the cross section a-a should be limited to 13.9 ksi. Determine the maximum value the offset distance "x" to meet this requirement. Develop an appropriate free body diagram and determine the location of the neutral axis for section a-a.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

X A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section at a-a has a diameter of d = 3 mm and the hook is supporting a purse with a mass of 3 kg, determine the normal stress profile. For what value of y (using the coordinates pictured for section a-a) with the normal stress be zero. If it is never zero enter "nde" for "not defined". N -L→ a. a AB C Follow sign convention that tension is positive and compression is negative. Normal stress at point A, σA= MPa Normal stress at point B, σB = MPa Normal stress at point C, σc = MPa y position where normal stress equals zero = mm Section a-a d
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
A pivoting cantilevered chair support is proposed for an industrial equipment application. If the maximum person weight is 180 lb, determine the greatest distance the chair can extend from the pivoting support at A. The cantilever is made from 1"x3" aluminum tubing with an allowable normal stress of 20 ksi. Also determine to the nearest 1/8" the diameter of the steel pin at A needed for the chair support to pivot about. Use 10 ksi as the allowable shear stress for steel. 180 1 in. 3 in 2.5 in. --0.5 in. 8 in.
The vertical links (at BD and CE) have a thickness = 5.4 and width = 31.2 mm uniform rectangular cross section. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E and choose the correct options. Applied load is 18.9 N, diameter of the pin is half of the width. All the options have been rounded off to two decimal places. 0.4 m 0.25 m 0.2 m O a. The stress in member BD is =0.18 MPa O b. The stress in member BD is =0.09 MPa O c. The stress in member BD is =-0.07 MPa O d. The stress in member BD is =-0.14 MPa O e. The stress in member CE is =-0.04 MPa O f. The stress in member CE is =-0.07 MPa O g. The stress in member CE is =-0.18 MPa O h. The stress in member CE is =-0.18 MPa
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in Ib/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in. 12 in.- 16 in: CAR = units %3D II
3. A pivoting cantilevered chair support is proposed for an industrial equipment application. If the maximum person weight is 180 lb, determine the greatest distance the chair can extend from the pivoting support at A. The cantilever is made from 1"x3" aluminum tubing with an allowable normal stress of 20 ksi. Also determine to the nearest 1/8" the diameter of the steel pin at A needed for the chair support to pivot about. Use 10 ksi as the allowable shear stress for steel. 180 1 in. 3 jn. 2.5 in. 0.5 in. - 8 in.
Determine the maximum compressive stress in the bracket at section a–a when the load P = 52 kN is applied at x = 300 mm.
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.5 m. Assume a = 0.7 m and b = 1.3 m. A B MPa x a Answer: 0 = i b
The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.9 m. Assume a = 0.6 m and b = 1.0 m. B MPa a Answer: 0 = i b
A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads. Determine the state of stress at point A. OX= Ixy = Given: The area moment of inertia of a solid circular cross section about its neutral axis is INA = (TR4)/4. The polar moment of inertia of a solid circular cross section about its neutral axis is JNA = (TR4)/2. The centroid of a semi-circle is located at 4R/(3n) from the horizontal axis representing the diameter line. 1500 N -37 Mpa 64 Mpa 3.5 Mpa 7.3 Mpa 600 N 37 Mpa -7.3 Mpa 300 mm 100 N·m 800 N 100 mm B
For the given truss system, determine the normal stress in member bE if its cross- sectional area is 5 in² and indicate whether tensile or compressive stress. D 12 ft A C G H E |-9 st---9 ft---9 ft--9 ft 80 kips 80 kips 80 kips