= For the image at the right. the coordinate angles are a = 66°. B 125°. v = 45°. and the point along a-a is (11, -6, 2). What is the angle between lines a-a and b-b? b-b (x,y,z) a a-a X Z β 2 Three cables are applied to an anchor as shown. The top force, F₁ = 38 N, is applied at an angle, = 39°, from vertical. The second force, F2 = 21 N, is applied through point (3.2.-1.6). And a mass = 2438 g (grams) is hung vertically from the anchor. What is the magnitude of the resultant force? F₁ |(0,0)| Mass F₁₂ 2 (x,y)

required drawing of problem and show your complete solution and formula provided in pic thanks.

Please help. Written on paper not typed on computer or keyboard please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.

True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in1999 as there was a unit conversion mismatch error between Lockheed Martin and NASA. Themismatch was in the thruster force units. NASA used the SI system which called forNewton-Seconds (4.45 times as large) of thrust and Lockheed Martin used Pound-Force Seconds.Calculations placed the Orbiter at 68 miles from the surface as it went into orbit, but it waswithin 57 km of the surface after the breaking maneuver. Any distance from the surface lessthan 50 miles would have caused the Orbiter to crash.a. What was the actual distance of the Orbiter from the surface in miles?b. In percentage, how far off from the calculated 68 miles was the Orbiter?

mmetri Each part has a constant thickness with values indicated. 2.0 mm 1.5 mm 3.0 mm 2.0 mm A shear force, S₂ is applied. This results in shear flow, shown with red arrows, which has the following values: • Shear flow in part 13, just before point 3 - 38 N/mm Shear flow in part 23, just before point 3 = 44 N/mm Shear flow in part 43, just before point 3- 44 N/mm What is the shear stress in part 35, just below point 3? Express your answer in MPa, to 2 decimal places but without the units included. You have a 3% margin of error.

ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an 8,200 kilo Pascals enters a turbine and leaves at 10 kPa. What is the entropy of the leaving steam if the efficiency of the turbine is 0.76. Round the answers in to 2 decimal places. Hint: Turbine's efficiency is the ratio of work delivered by the actual turbine to the work delivered by an isentropic turbine (no entropy change)   H (kJ/kg) S (kj/kg-K) 8200 kPa, 400 degrees 3137.6 6.3534 10 kPa, sat. liquid 191.832 0.6493 10 kPa, sat. vapor 2584.8 8.1511

This is the full question please if you unable to answer let me know, don’t provide me with wrong answer please

Topic/s: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation,Moment of a Force-Vector Formulation, and Principle of Moment.   Reminder: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after.   Thank you.

Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…

Do not copy paste the solution from outside. The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch.