For the given program: x-int(input("Enter a number:") gid-0 fin-0 while(x-0): gid=x% 10 fin-fin+gid X=x/10 print("The sum of digits is:",fin) Final Assignment Fill the values in the table below for every iteration of the loop:[first step is example): gid fin 148 14 Repeat the table for the following values of x: a. 526 b. 847 c. 914 d. 752 e. 439

For the given program: x-int(input("Enter a number:") gid-0 fin-0 while(x-0): gid=x% 10 fin-fin+gid X=x/10 print("The sum of digits is:",fin) Final Assignment Fill the values in the table below for every iteration of the loop:[first step is example): gid fin 148 14 Repeat the table for the following values of x: a. 526 b. 847 c. 914 d. 752 e. 439

Microsoft Visual C#

7th Edition

ISBN:9781337102100

Author:Joyce, Farrell.

Publisher:Joyce, Farrell.

Chapter5: Looping

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Similar questions

Convert the following for loop to a while loop: for (int x = 50; x > 0; x--){ cout << x << " seconds to go.\n"; }
Looping Construct with Floating Point Numbers Write a program that utilizes a while-loop to read a set of five floating-point values from user input. Include code to prevent an endless loop. Ask the user to enter the values, then print the following data: Total Average Maximum Minimum Interest on total at 20% Answer:
//for loop practice/*create a program, called aveRaceTime.cpp, for runners that wish to know their average race time.ask the user how many races they ran, and use their input in your for loop,for the limit on the number of loops (for example, if the user inputs three,that means your for loop should run three times.) Each time the loop runs, itwill ask the user what their race time was in minutes. Keep a running total ofall of the race times added together. After the loop, compute the user's average racetime, and display it in a sentence. Format the average time so it always shows two decimal points.
Factorials The factorial of n (written n!) is the product of the integers between 1 and n. Thus 4! = 1*2*3*4 = 24. By definition, 0! = 1. Factorial is not defined for negative numbers. Write a program that asks the user for a non-negative integer and computes and prints the factorial of that integer. You'll need a while loop to do most of the work-this is a lot like computing a sum, but it's a product instead. And you'll need to think about what should happen if the user enters 0. 1. 2. Now modify your program so that it checks to see if the user entered a negative number. If so, the program should print a message saying that a nonnegative number is required and ask the user the enter another number. The program should keep doing this until the user enters a nonnegative number, after which it should compute the factorial of that number. Hint: you will need another while loop before the loop that computes the factorial. You should not need to change any of the code that computes the…
Use While loop to solve the problems Note: Python language for solution 4. Write a program that uses a while loop, the program should do the following: The program should repeatedly read numbers until the user enters "done". Once "done" is entered, print out the total, count, and average of the numbers. 5. Write a program to find the sum of even numbers until n, where n is an int entered by the user, example: n = 11, sum = 2+4+6+8+10, sum = 30.
Basic while loop expression. Write a while loop that prints userNum divided by 4 (integer division) until reaching 2 or less. Follow each number by a space. Example output for userNum = 160:40 10 2 Note: These activities may test code with different test values. This activity will perform four tests, with userNum = 160, then with userNum = 8, then with userNum = 0, then with userNum = -1. See "How to Use zyBooks".Also note: If the submitted code has an infinite loop, the system will stop running the code after a few seconds, and report "Program end never reached." The system doesn't print the test case that caused the reported message.
II Home Take Test: Final Exam * Question Completion Status: QUESTION 2 x- 5 while(x<-4): print(x) x - x +1 print("While loop test") What is the output of the code above?
Python Coding-While Loops (In PyCharm Community edition) Create a while loop that SUMS up ALL the numbers given from an initial number and an ending number. Example would be : Input1 : What is the first number? 0 Input2 : What is the last number? 3 DO NOT SHOW but these are the computations inside the code : 0 + 1 + 2 + 3 = 6 This is the Output : The sum of all the number from 0 to 3, is 6 In the code you are going to use a total variable and add each additional time it runs through the loop to that total. REMEMBER the assignment from the first unit of programming where we used this formula : BUT you are going to create your own method using a while loop to emulate what formula accomplishes WITHOUT using this formula. The user will put in the first number and the last to be SUMMED - you will use the while loop to calculate all of the additions leading to the final number.
1.Convert the while loop in the following program to for loop. #include int main() { Int num rem,reverse_num3%3; printf("nEnter any number:"); scanf("%d",&num); while(num>=1) { rem=num%10; reverse_num=reverse num*10+rem; num=num/10; printf(nReverse of input number is:%d",reverse_num); return 0:
a and b are int variables containing values, and a > b.Write a for loop that prints numbers from a to b (both inclusive) divisible by 7.(Example: if a=74, b=16, then it will print 70 63 56 .... 21)Write only the for loop with its block, nothing else.
Convert the following for loop definition to a do while loop: for(int j= 100; j > 0; j--) { if (j % 2 != 0) System.out.println (val); }
n a while loop, generate a random integer from 0 to 9. Use srand() only once. Keep track of the number of iterations and quit the loop when the random integer is equal to 5. Report the number of iterations.