For the following peak or rms values of some important sine waves, calculate the corresponding other value: (a) 117 V rms, a household-power voltage in North America (b) 33.9 V peak, a somewhat common peak voltage in rectifier circuits (c) 220 V rms, a household-power voltage in parts of Europe (d) 220 kV rms, a high-voltage transmission-line voltage in North America

For the following peak or rms values of some important sine waves, calculate the corresponding other value: (a) 117 V rms, a household-power voltage in North America (b) 33.9 V peak, a somewhat common peak voltage in rectifier circuits (c) 220 V rms, a household-power voltage in parts of Europe (d) 220 kV rms, a high-voltage transmission-line voltage in North America

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ses Electron Lab Evening 21-1 > 28 November-4 December > Midterm Lab Exam 2020/2021 the sine wave input is SOsin50t. In half wave rectifier, If the load resistance is of 2KQ, then average DC power output will be? 00 Select one: a. 6.77V b. 1.25V C.5.97V d. 3.99V
In a phase controlled full wave rectifier, the source voltage is 50 VRMS sinusoidal, the source frequency is 60 Hz and the load is 20 ohms. Since the delay angle in the circuit is 20 °, which of the following is the value of the RMS load voltage? a) 99.54 V b) 49.77 V c) 70.38 V d) 35.19 V e) 23.46 V
a1.Using a dc and ac voltmeter to measure the output signal from a filter cicruit, we obtain readings of 25 v dc and 1.5 V rms.Calculate the ripple of the filter output voltage. a2. 2 a dc voltage provides 60v when the output is unloaded.When connected to a load, the output drops TO 56 V. calculate the value of voltage regulation.
a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R = 1092, L=20 mH, and a = 60°. Determine: i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. Vs S₁ S4 Figure $3 $₂ Lo Vo
Three Phase Full-Wave Fully Controlled Rectifier when highly Inductive load is connected: i. Draw graphs when α = 30, 60, 90, 120, 150 degrees. ii. Derive the output average voltage. iii. Derive the output rms voltage.
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
Q1: Draw the circuit of full wave rectifier mentioned on the circuit all equipment requirements to measure input and output voltages and the circuit current take in consideration voltage source 100v rms and load of 15k2 and device required to draw output signal, find the following: a. Calculate output current and voltages. b. Find input and output powers and the efficiency. c. Draw input and output voltages and output currents mentioned the amplitudes. d. What is the PIV of full wave bridge rectifier? And how many types of full wave rectifiers?
A full-wave rectifier operating from the 60-Hz ac supply produces a 20-V peak rectified voltage. If a 200-uF capacitor is used, calculate the ripple at a load of 120 mA. Ripple- 1.44 A Full wave rectifier operating from the 60Hz ac supply produces a 20-V rectified voltage. If a 200-uF capacitor is used, calculate the ripple at a load of 120 mA
: Find the average and rms values of the sinusoidal voltage measured at the output of full-wave rectifier.
A single-phase rectifier has a resistive load of 15 Q. Determine the rms current and the peak reverse voltage across each of the diodes in a) A bridge rectifier containing an AC generator with a voltage effective 220 V at 60 Hz. b) A rectifier with a medium tapped transformer with an effective voltage of 110V in each half of the secondary winding. must be performed in PSIM to show the correspondence and comparison of results obtained
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph