For the following beams, draw the simplified free-body diagram and below it the shear and bendir moment diagrams. Show all necessary solutions. Let the analysis be from left to right. Determin the points of zero shear (if any), their distance from point A, and the bending moments at the points. Indicate the value of all the points, degree of all curves, and the maximum shear an maximum bending moment of the beam. Use the area method. The two beams shown are connected by an internal hinge at Cand are supported by a fixed support at A and a roller at D. P = 256 N W₁ = 210 N/m W₂ = 314 N/m M=409 N.m W₁ PH Pad Fay ropery CoD M CO mtenis mal. The M or couniction of mater.. W₂ 2m 2m Use the following tables as template for your solution. 5m Shear Calculation Relation of Shear to Concentrated and Distributed Load V₂ - V₁ = Bending Moment Calculation Relation of Bending Moment to Applied Moment and Shear Diagram M₂-M₁= unde de and the pyrig such ingen. youn party a anywa Shear Values (N) V₁ = MA= M₂= (N) ActXA) 293 of "Intellectual Property de 3. Any reproduct and/or omic

For the following beams, draw the simplified free-body diagram and below it the shear and bendir moment diagrams. Show all necessary solutions. Let the analysis be from left to right. Determin the points of zero shear (if any), their distance from point A, and the bending moments at the points. Indicate the value of all the points, degree of all curves, and the maximum shear an maximum bending moment of the beam. Use the area method. The two beams shown are connected by an internal hinge at Cand are supported by a fixed support at A and a roller at D. P = 256 N W₁ = 210 N/m W₂ = 314 N/m M=409 N.m W₁ PH Pad Fay ropery CoD M CO mtenis mal. The M or couniction of mater.. W₂ 2m 2m Use the following tables as template for your solution. 5m Shear Calculation Relation of Shear to Concentrated and Distributed Load V₂ - V₁ = Bending Moment Calculation Relation of Bending Moment to Applied Moment and Shear Diagram M₂-M₁= unde de and the pyrig such ingen. youn party a anywa Shear Values (N) V₁ = MA= M₂= (N) ActXA) 293 of "Intellectual Property de 3. Any reproduct and/or omic

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

for the beam and loading shown (a)use discontinnuity functions to write the expression for w(x). include the beam reactions in this expression. (B) intergrate w(x) twice to determine v(x) and m(x). (C) Use v(x) and m(x) to plot the shear- force and bending- moment diagrams.
(b) Figure Q1(b) shows the steel truss with a 3-meter span. The cross-sectional area for all members of the truss is 400 mm?. Span BC carried a uniformly distributed load of 30 kN/m. Prove that the plane truss is internal statically indeterminate. Then, using the Method of Virtual Work, approximate the member forces AC. Assume that member AC is redundant in your analysis. Given Es = 200 GPa. All answers are in three decimal places. B 30kN/m C 4m A 3m FIGURE Q1(b)
Solve for displacement at C and D using Conjugate Beam Method
Figure Q1 shows a statically determinate plane truss subjected to a verticalconcentrated load at C and E. The truss is made using steel with Modulus of Elasticity is210 GPa, and the cross section area for all members are 30 mm2. Assuming P is the 10 and a is half of P, determine the vertical displacement at F. Thesolution can be based on Method of Conservation Energy or Method of Virtual Work.
Determine the maximum deflection of the steel beam shown. Take E= 200GPa and I = 60(10^6)mm^4. Hint: the maximum deflection occurs at zero slope same as the highest moment occurs at the point of zero shear. Using Conjugate beam method.
Find the shear force at 1m to the right of A, showing the equation and all steps used to calucalte the value. (Ay = 7.06kN and By = 3kN) Need only a handwritten solution only (not a typed one).
The bending stiffness of the beam given the loading condition in the figure is El. Determine according to this with donmy Mohr method at point A
Problem 2 -A concentrated couple, = 600 Nm acts at the center of the simply Supported beam which is also asted upon by the distributed load shown in the figure. Assume that the beam itself is weightless. (a) Find the internal shear Vx) and moment M(x) as a functions of x. (b) Draw the shear and moment diagrams. Label the values at x = 0, x = 6, x = 12, and at any point where V(x) or M(x) is a local maximum or minimum. y 50 N/m Mo 6 m 6 m
Determine the displacement and the rotational at point D, considering that the moment of inertia I=300 in4, the elastic modulus is the same for the section of the beam with a value of E=29000 Ksi. Use Castigliano's method for beams. Point D is half the distance from segment AB. The following figure shows the applied loads, distances, and conditions at the beam supports.
The bending stiffness of the AB section is 2EI in the cantilever beam, whose loading condition and dimensions are given in the figure, Since the bending stiffness is EI, the collapse and rotation at the point C can be calculated by using virtual work theorem. calculate. The cutting effect will be neglected
A variable cross-sectional beam is pinned from the point B by BD bar as shown. Flexural rigidity of AB and BC beams are 2EI and EI, respectively. If the axial rigidity of the BD bar is EA, Determine the reaction forces at the point A by using, a) Superposition method b) Mohr method c) and show whether the results are overlap or not. I=(7*A*L^2)/3
QUESTION 3: Since the bending stiffness of the AB section is EI and the bending stiffness of the BC section is 2EI in the cantilever beam whose loading condition and dimensions are given in the figure, calculate the collapse and rotation at the point C using the virtual work theorem. The cutting effect will be neglected.