For the flow shown in the figure below, the stream function is = {4ri sin( 0)} where r is in meters. If the pressure at the origin O is 20 kPa (gauge), determine the pressure at R = 2m, 0 = 45°. Take density d. 950 kg / m³ %3D 'B 45 O 41.45 kPa O 16.81 kPa O 21.45 kPa O 1.53 kPa O -1.45 kPa O 1.53 kPa

For the flow shown in the figure below, the stream function is = {4ri sin( 0)} where r is in meters. If the pressure at the origin O is 20 kPa (gauge), determine the pressure at R = 2m, 0 = 45°. Take density d. 950 kg / m³ %3D 'B 45 O 41.45 kPa O 16.81 kPa O 21.45 kPa O 1.53 kPa O -1.45 kPa O 1.53 kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a pipe reducer shown in figure 2. The static pressure in the large diameter pipe and the small diameter pipe are measured by the inverted U-tube manometer containing oil of specific gravity less than one. Determine the manometer reading, thus show that h is given by the equation h = ng(1-SG) la SG Water Figure 2 The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B.
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
7. Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as shown in the Figure. The flow of water in the pipe is 12cfs. Assume n=0.013 and neglect minor losses. Determine the following: (a) The velocity of flow in the pipe in fps. (b) The total head lost in the pipe in feet, (c) The pressure at the top of the tank in psi. D=4" 20 D=4" 100 P=? 10 WATER D-4" 40
1.) A pressure in a given tank reads 398 mm of Hg. Determine the equivalent height of a certain fluid in m with sp.gr= 4.33.
Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B в is 87 kPa, estimate the pressure at A, in kPa. Assume all fluids are at 20°C. ywater =9790 N/m', Ymercury =133100 N/m2, yoil =8720 N/m³ SAE 30 oil Gage B Mercury 6 cm 5 cm Water flow 11 cm 4 cm
Question 2. The manometer in the figure is used to measure the pressure difference between two points in the pipe. The density of the water in the pipe is 1000 kg/m3 and the valve is open. If the readings on the manometer are z1= 100 mm, z2= 250 mm and h= 90 mm, how many N/m2 is the difference between P1 and P2? watplf Valve aik
The tank is filled with water and kerosene to the depths shown in (Figure 1). The tank has a width of 3.0 m Take p = 1000 kg/m³, p = 814 kg/m³. Figure A 60° 3 m B 1 of 1 1 m Part A Determine the total resultant force the liquids exert on side AB of the tank. Express your answer to three significant figures and include the appropriate units. FR = μA xa Xb Value a b Provide Feedback Units X. 10m Submit Previous Answers Request Answer X X Incorrect; Try Again; 5 attempts remaining ? www Next >
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
3. IN THE FIGURE SHOWN, THE 50-METER PIPE IS 60 MM IN DIAMETER. THE FLUID FLOWING HAS MASS DENSITY OF 920 KG/CU.METER AND DYNAMIC VISCOSITY OF 0.29 PA-S. THE PRESSURE IN THE ENCLOSED TANK IS 200 KPA GAGE. DETERMINE THE FOLLOWING(ƒ =0.0225). A. THE AMOUNT AND DIRECTION OF FLOW B. THE VELOCITY OF FLOW IN THE PIPE. C. THE REYNOLDS NUMBER OF THE FLOW H= 12 m L=50 m
A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in diameter. If 2 liters of water per minute flow upwards through the pipe the pressure difference across the pipe is 35 kpa. Calculate the flow downwards through the pipe if the pressure across the pipe is to be zero. The losses across the pipe are given by h1=k((v2) ²-(v1)²)/2g,where v1 and v2 are the velocities in the 50 mm and 25 mm sections respectively.
Consider an oil flow of 14 m³/h in a long, straight and smooth pipe with diameter of 4 cm. What is the pressure loss per meter? Oil absolute viscosity is 0,1 kg/ms and density is 900 kg/m³. Friction factor for laminar flow can be calculated from 64 f = be Re Round off the answer to an integer in Pa/m, but enter the answer without the unit. 0.1 0.09 0.08 0.07 0.06 0.05 0.04 f 0.03- 0.025 0.02 0.015 0.01 0.009 0.008 Laminar flow 10³ 1 1 Transition range I 2(10³) 468 104 Wholly turbulent flow Smooth ī 2(10¹) 468 105 2(105) 4 6 8 106 Re PVD μ 2(105) 4 68 107 2(107) 4 6 8 0.05 0.04 0.03 0.02 0.015 0.01 0.008 0.006 € 0.004 D 0.002 0.001 0.0008 0.0006 0.0004 0.0002 0.0001 0.00005 0.00001
7. In the figure shown, determine the value of z when the pressure at A is 10 psi greater than at B . water 2ft Hg/