Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of the shear and bending moment in the beam by the semi-graphical method. SHOW COMPLETE SOLUTIon. 24 kN 29 kN/m B A D -3 m 2 m 1 m

Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of the shear and bending moment in the beam by the semi-graphical method. SHOW COMPLETE SOLUTIon. 24 kN 29 kN/m B A D -3 m 2 m 1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight…

Q: Compute the allowable resisting moment used the transformed Area method. are fc=1800 fs= f's = 24000…

A: Calculate allowable resisting moment Working stress method Transformed area method

Q: ear and bending-moment diagram for the beam and loading shown, and Osolute value (a) of the shear;…

Q: A non-prismatic beam is loaded as shown. The tributary width that was used is 3m. Find all the…

Q: Q2: For the loaded beam shown below, determine value of delection at point B. Take I=10x10 mm' and…

A: Given:- A beam is loaded with uniform load and varying load The magnitude of uniform load = w = 4…

Q: Slope Deflection Method Instructions: Solve the following problems completely using Slope Deflection…

Q: 4. The difference in elevation between line AB is 6.5 m. A 100 meter steel tape was used with a…

A: Given:- Difference in elevation between line AB=6.5m Pull=12kg temperature=30 degree Celsius during…

Q: Situation 7: Considering the same figure as above, the towline exerts a force P =4 kN at the end of…

Q: For the simple beam loaded as shown, determine the value of Elō at C, 2m from the left support, and…

A: From the given question it is required to calculate the deflection at C by using area moment and…

Q: For the beams and loading shown, using the graphical method: (a) draw the shear and bending moment…

A: To find: (a) Draw the shear force and bending moment diagram. (b) Determine the…

Q: 4 kN/m A C 2 m 8 kN 5 m D 8 kN 2 m B

Q: 1. Calculate the design moment capacity þMn of the beam if fc 28 MPa and fy = 420 MPa 2. Check…

Q: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential…

Q: A propped beam shown below is loaded with UDL along its entire span. Determine the following: a.…

A: Find reaction R Moment at C And deviation (tB/C)

Q: mine the equations of the shear and bending moment curves for the beam and loading shown , (b) draw…

Q: Analyse the frame in Figure 1 using the Slope-Deflection Method. Draw the shear force, axial force…

A: First, we need to calculate the reactions at the supports. The total load on the frame is the…

Q: 69 KN/m 41 KN В C D А L= 1.5 m L= 2.2 m L= 3.6 m RD RB

Q: Write shear and moment diagram for the beam. Specifying values at all change of loading positions…

Q: 300 N/m 2.7 kN • m +3 m -- 3 m-+ 3 m--3 m-

A: Elastic curve equation: The equation of the elastic curve is determined by differentiating the…

Q: IINSTRUCTIONS: DETERMINE THE MAXIMUM SHEAR (V) AND MOMENT(M) OF THE BEAM. AND SKETCH THE SHEAR FORCE…

A: A loaded beam is given and it has been asked to determine shear force and bending moment diagram.…

Q: Draw the shear and moment diagram, and the elastic curve of the loaded frame shown. Show complete…

A: Shear force is the internal force on a member when the force is not applied at the axis. Shearing…

Q: An I-section beam shown is subjected to a shear force of 50 kN. Find the magnitude and position of…

A: Maximum shear stress: It is defined as the maximum shear stress which occurs at a small portion of…

Q: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential…

Q: 6. Determine the shear and moment equation as function of x distance for the beam shown and then…

A: The given beam is composed of two loading Uniformly distributed load of 5 kN/m. Uniformly varying…

Q: Sketch the shear and moment diagrams of the beam loaded as shown. Also, determine the values of…

Q: Draw qualitative bending moment diagrams on both tension and compression side of the beams shown…

A: Draw qualitative bending moment diagrams on both tension and compression sideof the beams shown…

Q: 2. (Problem 5.50 from the text book) Determine (a) the equations of the shear and bending- moment…

A: Find: (a) Equations of the shear and bending- moment curves for the beam and loading (b) Maximum…

Q: Calculate the reactions and draw the shear and moment diagram for the three- span continuous beam…

A: EI is constant We are required to draw the Shear and Moment diagram for the continuous beam by using…

Q: For the beam given in the figure, a) Find the support reactions. b) Draw the normal force, shear…

Q: Using PLASTIC ANALYSIS, determine the plastic moment on the given beam below. 7 kN/m 3.5 m O 11 kNm…

A: Number of plastic hinge n = Ds + 1 Ds = Number of reaction force - equilibrium equation = 4 - 2 = 2…

Q: The beam shown has a rectangular cross section 120 mm wide and 200 mm high. Draw the shear and…

Q: 69 KN/m 41 KN B C D А L= 1.5 m L= 2.2 m L= 3.6 m RD RB

Q: A propped beam shown below is loaded with UDL along its entire span. the foll

Q: For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the…

Q: Continuous Beam Has A Loading Shown. Assuming Constant Flexural Rigidity (EI). Use Three-Moment…

Q: Determine the deflection of the deformed beam at point A.

A: Deflection: - It is defined as the vertical displacement of a point of a beam from actual position…

Concept explainers

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.

Question

Draw the shear and bending moment curves for the beam and loading and the maximum
absolute value of the shear and bending moment in the beam by the semi-graphical method.
SHOW COMPLETE SOLUCION.
24 kN
29 kN/m
В
A
D
000
3 m
2 m
1 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

) Determine the moment gradient modifier of a 12 m simply supported beam having auniformly distributed load W.
SOLVE FOR THE REACTIONS AND DRAW THE SHEAR AND MOMENT DIAGRAMS OF THE FOLLOWING BEAMS PROVIDE A SOLUTION USING BOTH; THREE-MOMENT EQUTION (3ME) AND SLOPE DEFLECTION METHOD (SDM) ASSUME w = 12 kN/m P = 46 kN El = constant P kN w kN/m B A 3m 2m * 4m
Statics please help a.) Derive the appropriate equations for shear and bending moment throughout the beam. Measure x-distance from the left side of the beam and make sure to tell where each equation is applicable. b.) Draw the shear and bending moment diagrams for the beam.
Perform the following. Write the Shear and Moment Equations b. Draw the Shear and Moment Diagrams а. С. Draw the Elastic Curve d. Indicate where the Point/s of Zero Shear е. Indicate where the Point/s of Contraflexure 3 m 3 m 3 m B B 90 kN/m
1.) Solve, show complete solution, and fomula used.
A propped beam shown below is loaded with UDL along its entire span. Determine the following: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential deviation at point B with respect to point C (t B/C) A d 4kN/m Ţ 3M
PLEASE MAKE THE SOLUTION COMPLETE and UNDERSTANDABLE Show fbd to your solution.
Use black/Blue A continuous beam (El is constant) is loaded as shown and is to be analyzed using Slope Deflection Method. Illustrate Shear and Moment Diagrams. Also, determine the deflection at D. 6 m 30 kN/m 9 m 4m 10 kN
6 of 8 H.W.6: For the longitudinal frame of the flat slab floor shown in figure, and by using the Direct Design Method, find: a- Longitudínal distribution of the total static moment at factored loads. b- Lateral distribution of moment at exterior panel (column and middle strip moments at exterior support). Given w = 18.0kN/m², edge beams: 300 x 600 mm. 5000 mm 6000 CL Panel 2000 CLPanel 9400mm -400 5000 mm H.W.7: For the transverse exterior frame (Frame D) of the flat plate floor, without edge beams, shown in Figure, and by using the Direct Design Method, find: 120k
Problem 1 A continuous beam loaded as shown with a constant El all throughout the span of the continuous beam. Using moment distribution method (perform 5 iteration) determine the following: 60 kN ... 20 kN/m В 8 m 8 m 4 m 4 m Moment at support A in kN.m. Ans.: Blank 1 kN.m. Blank 1 Add your answer Moment at support C in kN.m. Ans.: Blank 1 kN.m. Blank 1 Add your answer Reaction at support B in kN. Ans.: Blank 1 kN Blank 1 Add your answer
a)Using Macaulay's method to set up an equation for the whole beam and determine the bending moments at 1 meter intervals b)Find out the maximum bending moment and where it occurs; sketch a fully dimensioned bending moment diagram.
A propped beam shown below is loaded with UDL along its entire span. Determine the following: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential deviation at point B with respect to point C (t B/C) A d 4kN/m Ţ 3M