For the figure shown, A compound shaft composed of bronze, aluminum and steel segments is fastened to rigid supports. For bronze, G = 35 GPa; for aluminum, G = 28 GPa and for steel, G = 83 GPa. Compute the maximum shearing stress(in MPa) developed in aluminum segment. O 193.54 4.33 O 132.41 O 102.56 O133.78 O 193.54 O4.33 O 132.41 102.56 300N-m 700N-m O 133.78 Bronze D=25mm L=1.5m Compute the maximum shearing stress(in MPa) developed in bronze segment. Aluminum D=50mm L=2.0m Steel D=25mm L=2.5m

For the figure shown, A compound shaft composed of bronze, aluminum and steel segments is fastened to rigid supports. For bronze, G = 35 GPa; for aluminum, G = 28 GPa and for steel, G = 83 GPa. Compute the maximum shearing stress(in MPa) developed in aluminum segment. O 193.54 4.33 O 132.41 O 102.56 O133.78 O 193.54 O4.33 O 132.41 102.56 300N-m 700N-m O 133.78 Bronze D=25mm L=1.5m Compute the maximum shearing stress(in MPa) developed in bronze segment. Aluminum D=50mm L=2.0m Steel D=25mm L=2.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DEFORMATION DUE TO AXIAL FORCES PROBLEM 1: CE Brd Exam The rigid block shown weighs 176.4 kN. It is held in position shown with stress in the supporting rods shown initially zero. If the former is to remain horizontal when released, 1a. Find the ratio of forces in bronze and steel a. 0.389 c. 0.397 1b. Find the stress in the bronze rod. b. 0.344 d. 0.416 а. 31.92 MPа с. 28.73 МPа 1c. Find the the elongation of steel rod. b. 53.34 MPa d. 39.67 MPa a. 0.615 mm b. 1.83 mm c. 2.31 mm d. 2.12 mm 0.6 m BRONZE A=900mm STEEL STEEL A=600mm A=600mm 1 m E-200GPA E-83GPA E=200GPA W = 176.4 kN
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
For the shown Fig., find the maximum shearing stress in bronze part of the shaft. * Steel d= 200mm Bronze d= 100mm G= 40GPa G= 30GPa 2KN.m Aluminum d= 100mm G= 80GPa 8kN.m 3kN.m 3m 2m 1.5m 2.55 MPa 2.85 MPa 3.55 MPa 25.47 MPa 28.5 MPa 35.5 MPa 19.2 MPa none of these العربية الإنجليزية
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
Q2: For the shaft shown in Figure 2, find the maximum shearing stress in the Aluminum and the steel and the total angle of Twist. Use G aluminum =28 GPa. G steel =83 GPa. Use the data in Table 2 Figure 2
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E = 200 GPa, Compute the deformations of the steel bars. A B 7,500 N 6.00m C 8.00m
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two- dimensional stress, o =310 N/mm2 (tensile) and Oy=300 N/mm² (compressive). E=2x105 N/mm², Poisson's ratio μ-0.3. The elongation of the bar is the direction of a will be