For the CRO display of a pulse waveform, the time/cm is on 21 ms/cm and the volt/cm switch is on 9 V/cm. The width of one complete cycle is 9.7cm and the height of the pulse is 4cm. Determine the RMS value of the pulse waveform. 18.00 O 1.71 25.46 O 11.56

For the CRO display of a pulse waveform, the time/cm is on 21 ms/cm and the volt/cm switch is on 9 V/cm. The width of one complete cycle is 9.7cm and the height of the pulse is 4cm. Determine the RMS value of the pulse waveform. 18.00 O 1.71 25.46 O 11.56

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Identify the Peak to Peak value of the given waveform. 3 1 -1 -2 -3 ms -4 O a.0 O b.4 O .8 O d. -4

A: In this answer let us try to find out the peak to peak value of the given waveform as shown below.

Q: The figure below shows a periodic voltage waveform. Determine: a) Period b) Frequency c)…

A: Any time domain signal can be sinusoidal, DC signal or any curve signal. Sinusoidal signals are…

Q: For the given waveform the peak voltage is (V) and frequency is (Hz). Trig Vertical Pos Horizontal…

A: Given waveform: To find: Peak voltage and frequency?

Q: 6. A periodic voltage has the following voltages: 15 V at 0.02 sec, 9 V at another 0.05 sec and 0 V…

Q: The voltage waveform during the first half cycle are from t = 0 to t = 0.01 increases linearly from…

Q: A double beam oscilloscope displays two sine waveforms A and B with peak to peak heights as A14 4 cm…

Q: Supply the signal generator and adjust the output to a sinusoidal voltage of 8V peak to peak –…

Q: If in a single phase full wave AC voltage controller, the firing angle of the SCRS are equal, then…

A: If in a single phase full wave AC voltage controller, the firing angle of the SCRS are equal, then…

Q: In an experiment, the function generator is adjusted to generate a square voltage at a certain…

A: Square voltage wave

Q: 06.) Show mathematically that the average value of a full-wave rectified sine wave of peak value Vm…

Q: How many degrees of phase difference are the two signals shown in this figure? If the time base…

A: To find the phase difference between signals First, find the period of the signal Divison…

Q: Apply Input : 10sin(wt) . Plot the output graph and express. Calculate the RMS. R1= 2kΩ

Q: Information: (2 Vp-p 50 Hz + 2 Vp-p 100 Hz) sine wave Carrier: 4 Vp-p 1000 Hz sine wave Calculate…

Q: Q3]. Draw a neat sine wave with a peak amplitude 110V and time period 3 sec. For the same waveform…

Q: For the CRO display of a pulse waveform, the time/cm is on 14.2 ms/cm and the volt/cm switch is on 5…

A: the correct option is b which is the approximated result because the actual time period is 0.22862…

Q: A 60 Hz sinusoidal voltage with an RMS value of 440 V is applied to a TRIAC voltage regulator. The…

A: it is asked to find the output DC voltage of given TRIAC voltage regulator

Q: Indicate the rms value and frequency in Hz of a voltage signal with value 200sen(1000t+30°) V

Q: 2.2kQ 10 µF V Figure 1: RC high-pass circuit schematic Peak: 9.2V RMS: 3.05V Calculate the…

A: The circuit can be implemented in tinker card are as follows as given The DC offset is =0 V

Q: In an experiment, the function generator is adjusted to generate a square voltage at a certain…

A: Given oscilloscope peak to peak voltage is 10Vp-p at certain frequency. Hence maximum voltage Vm=5V…

Q: 11. The effective value is the average of all the instantaneous values of an alternating voltage and…

A: 11. False 12. False 13. True 14. False 15. False

Q: The following figure indicates alternating(ac) quantity. SQuare wave Select one: O True O False

A: The definition of an alternating quantity may be defined as a quantity which reverses its direction…

Q: sinusoidal waveform is displayed on an oscilloscope and has a peak-to-peak amplitude of 15 V. At the…

A: In this question we will find analogue multimeter reading....

Q: A square waveform with following specifications. Peak to Peak current 10A Time for ten cycles 0.04s…

A: The square waveform of the current has the following specification: IPeak-Peak=10 ANumber of…

Q: For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 5ms/cm and the…

A: Here each square box is 1 cm x 1 cm And 1 cm length is divided into 10 parts.

Q: If the switching impulse wave peak is 90 I the tail time is the time between:

A: the switch impulse wave tail time is the time taken by the signal the 50% peak value.

Q: From the signal function below determine the period. Please answer in 10 minutes thank u

Q: Determine and sketch the output voltage waveform for the circuit shown if the sinusoidal signal at…

Q: Frequency of power supply is 50 Hz. The time period to complete 8 cycles in seconds is:

A: In this question, choose the correct option What is value from peak positive to peak negative? What…

Q: 4. Sketch the output waveform resulting in the opposite figure. V₁+1SV. 2002 0.1μF

Q: The rms value of the resultant current in a wire carries a dc current of 10 A and a sinusoidal…

A: Given- dc current- Id=10 A, ac current- Ia=20 A, To Find- The rms value of the resultant current…

Q: I: An incoming sine wave results in a gain of -5db. The output sine wave has a peak value of 1V.…

A: Given Data: An RC High Pass Filter has, Peak Output voltage Vb=1 V Voltage gain AV=-5 dB To Find:…

Q: What is the period of the signal

Q: 10 V ▲e 1₂ Sine wave A t₁ A In the plot of Sine wave A shown above, the value of t₁ is 15.0 ms.…

A: Given a sine wave, with t1= 15 ms. we are required to find various parameters for this waveform.

Q: Which one of the following is correct for Peak factor of a sine wave. O 1.41 O 1.73 O 1.11 O 2.41

A: GIVEN What is peak factor of sine wave

Q: The current waveforms of a capacitor are shown in Figure below. Determine the average, root mean…

A: Given:capacitor current waveform as,with Ipeak = 400A.we need to find:a) the average value of the…

Q: QUESTION 2 The peak-to-peak voltage is 40V, its rms voltage is 14.1 V 11.4V 13.3V 12.3 V

A: The peak-to-peak voltage, VP-P=40 V

Question

For the CRO display of a pulse waveform, the
time/cm is on 21 ms/cm and the volt/cm
switch is on 9 V/cm. The width of one
complete cycle is 9.7cm and the height of
the pulse is 4cm. Determine the RMS value
of the pulse waveform.
18.00
1.71
25.46
11.56

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the following wave forms Shown in Figure 2. Detemine the output if the five signals are ANDed. Detemine the output if the five signals are ORed. Draw the timing diagram for each case. 1 1
A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 30 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.8 cm and the peak to peak distance is 4.8 cm. Determine the following: The frequency is? The magnitude of the sine voltage is? The amplitude is? The R.M.S voltage is?
In sinusoidal voltage waveform the positive peak to negative peak value is O a. Three times the peak value O b. Two times the amplitude O c. Twice the times of average value O d. two times of RMS value
For the sine wave seen on the oscilloscope screen a -) amplitude B -) peak value c -) Hill to Hill value d -) period E -) frequencyf-) Find the active (rms) value.
Form factor is defined as O a. Average value / RMS Value O b. Average Value / Maximum Value O c. Maximum Value / RMS value O d. RMS value / Average Value
Determine the RMS Noise Voltage when the noise readings measured at several times has these values: 25mV= 2 times, -22mV = 3 times, 10mV and - 72mV = 8 times.
The ratio between the RMS values to the mean value is called as
For the sine wave shown below determine the peak-to-peak voltage. The Horizontal scale "time base" is 6 ms/div, the Vertical scale is 9 Volt/div. (Volt) +V Time (s) -V Vpeak-to-peak = Vpp
For the CRO display of a pulse waveform, the time/cm is on 15 ms/cm and the volt/cm switch is on 5 V/cm. The width of one complete cycle is 17.1 cm and the height of the pulse is 3cm. The time period will be seconds. O 25650.00 O 0.39 O 0.26 O 0.00
Please determine based off waveform A)peak amplitude B)peak to peak value C)average value
Show the steps
From the below figure, determine the approximate value of the pulse width (tw). Each horizontal division is 3.67 milliseconds and Each vertical division is 2 volts The result should be in ms Calculate Answers to 2 decimal points V (V) t (ms)