For the circuit shown below D1 and D2 are Ideal Diodes, R1 = R2 = R33D2 K2. The output of the rectifier is shown below: a) Determine the VDC for the Vo = 10V without a capacitor. b) Sketch Vs (in the secondary).. c) Calculate the Value of the Capacitor required to produce Vr = 0.04V. d) Determine the Turn Ration of the transformer, for the input votage Vp = 120V. M. %3D 10V e) What is the PIV? D2 D1 T=20 ms Vp R1 R3 loN R2

For the circuit shown below D1 and D2 are Ideal Diodes, R1 = R2 = R33D2 K2. The output of the rectifier is shown below: a) Determine the VDC for the Vo = 10V without a capacitor. b) Sketch Vs (in the secondary).. c) Calculate the Value of the Capacitor required to produce Vr = 0.04V. d) Determine the Turn Ration of the transformer, for the input votage Vp = 120V. M. %3D 10V e) What is the PIV? D2 D1 T=20 ms Vp R1 R3 loN R2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
For the given circuit below, a step down transformer gives an RMS voitage of 230 V/ 12-0-12 V with a load resistance of 22 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. O 33.94 O 26.83 O 16.97 O 21.17 A silicon diode in a half-wave rectifier has a barrier potential of 0.7 V. This has the effect of reducing the peak input voltage by 0.7 V. increasing the peak input voltage by 0.7v. no effect. increasing the peak output voltage by 0.7 V. Next nane
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
In a given circuit below is connected to an AC signal with 240V peak in a 4:1 transformer. Sketch the voltagewave form at VA and Vo as practical diode. (Show Complete Solution)
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KN resistor) and the load current (through the load 2.2 Kn resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode DI). The input V. is sinusoidal with maximum amplitude (peak) of 100 V and frequency of 700 Hz. The diode DI is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi