For the circuit shown below, an impedance having a constant phase angle of -36.87" is connected across the load terminals a and b in the circuit shown below. The magnitude of Ze is varied until th average power delivered is the most possible under the given restriction What settings of RL and XL transfer the most average power to the load? 10/0 V (rms) 3000 (2/4000 (2 #1 w Select one: O a. RL = 5000 and XL = = 0 b. R= 4000 and X₁= -3000 O c. RL= 0 and X₁= -3000 b -IXC

For the circuit shown below, an impedance having a constant phase angle of -36.87" is connected across the load terminals a and b in the circuit shown below. The magnitude of Ze is varied until th average power delivered is the most possible under the given restriction What settings of RL and XL transfer the most average power to the load? 10/0 V (rms) 3000 (2/4000 (2 #1 w Select one: O a. RL = 5000 and XL = = 0 b. R= 4000 and X₁= -3000 O c. RL= 0 and X₁= -3000 b -IXC

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
For the following voltage and current phasors in rms Voltage magnitude in (V) is 136 and phase angle in degree is 18 Current magnitude in (A) is 0.7 and phase angle in degree is 69 The power factor is: O 0.052 (lagging) O 0.951 (leading) O 0.777 (lagging) O 0.629 (lagging) O 0.629 (leading) O0.777 (leading)
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Prob. I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50 Ohms i,- 225 2253.13° = 190.92 + 254.56 VRMS R1 + R2 Vc = 237.17/26.565° = 212.13+ 106.07 VRMS 100 2 -3Z98.13° =-0.4243 + J2.970 ARMS C -j60 Ohms For this problem provide at least 3 digits of precision for the answers. The results for the following calculations are to be answered in - a) Find the current I b) Determine the real (P) and reactive(Q) power DELIVERED by the source c) Determine the real (P) and reactive (Q) power ABSORBED by each impedance ( resistors R1 and R2, inductor and capacitor). The values for P and Q can be positive or negative. Remember S =P+jQ, so do not include the j with your answer for Q. Each of these answers will require two parts. For the phasor a magnitude and angle will be needed. For the powers, The real power P and the reactive power Q are required.
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
2. A triangular voltage source has a peak value of 10 V. What is the computed RMS value of this source? a. 3 V b. 4 V c. 5 V d. 6 V 3. In Question 2, if the source is measured by an analog meter, will it show the correct RMS value? a. Yes b. No
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
A 15ohms resistor connected in parallel with an impedance of 8 - j2 across an AC source. The entire circuit takes a total average power of 2000 watts. What is the average power in the 15ohms resistor?
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?