If can answer all, much better. But please do answer the first sub parts as per code (a-c) For the built-up section shown, determine the following:a. Centroid of the Area,b. Moment of Inertia, Ik and I,c. Section Modulus, Sx and S,d. Radius of Gyration, Rx and Rye. Moment of Inertia with respect to x'-axis, with the x'-axis taken 30 degrees from the x-axis of the global centroid of the section.Note: the x and y-axes in the figure is to be used as reference lines, and do not necessarilyrepresent the global x and y-axes of the seetion.Y25.00--357.00-30.00-25.00700.00-30.0030.00

Answered: Image /qna-images/answer/ab9fc263-37e3-45dc-847c-16dfc66e1d38.jpg

For the built-up section shown, determine the following: a. Centroid of the Area, b. Moment of Inertia, Ī, and I, c. Section Modulus, Sx and Sy d. Radius of Gyration, Rvand Ry e. Moment of Incrtia with respect to x'-axis, with the x'-axis taken 30 degrees from the x- axis of the global centroid of the section, Note: the x and y-axes in the figure is to be used as reference lines, and do not necessarily represent the global x and y-axes of the section. Y 25.00- 357.00 30.00 -25.00 700.00 -30.00 30.00

For the built-up section shown, determine the following: a. Centroid of the Area, b. Moment of Inertia, Ī, and I, c. Section Modulus, Sx and Sy d. Radius of Gyration, Rvand Ry e. Moment of Incrtia with respect to x'-axis, with the x'-axis taken 30 degrees from the x- axis of the global centroid of the section, Note: the x and y-axes in the figure is to be used as reference lines, and do not necessarily represent the global x and y-axes of the section. Y 25.00- 357.00 30.00 -25.00 700.00 -30.00 30.00

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. Determine the x component of the centroid of the given area. y y= x y=1.44-x A
Consider the cross section shown in (Figure 1). Suppose that b = 112 mm Part A Determine the major principal moment of inertia Imar of the cross section about the principal axis having an origin at point C. Express your answer to three significant figures and include the appropriate units. ? Imax = Value Units Submit Request Answer Part B Determine the angle 0,, as measured on the cross-section from the positive z axis. Figure Express your answer using three significant figures. Enter positive value if the angle is counterclockwise and negative value if the angle is clockwise. Vol AEO vec ? 10 mm - Op, = 80 mm Submit Request Answer 80 mm. 10 mm Part C 10 mm - Determine the minor principal moment of inertia Imin of the cross section about the principal axis having an origin at point C.
Start For the figure shown, let a =200 mm and b 75 mm. b/2b/2 abus b. ents es a ea/2 a/2- Determine the coordinate of the centroid with respect to the given axes.
a. Determine the value of y bar b. Determine the value of I with respect to centroidal x axis
Consider the rod shown. Suppose that hℎ = 170 mm, r = 290 mm. Determine the location (x,y) of the centroid of the rod.
5/29 The thickness of the triangular plate varies linearly with y from a value to along its base y 0 to 2fg at y = h. Determine the y-coordinate of the center of mass of the plate. Ans. y = 3h/8 y - x to Problem 5/29
20. Situation 22. For the built-up shape shown in the figure, determine: a. The location of plastic neutral axis form the top edge of the flange in mm. ____ b. The plastic section modulus about the horizontal axis. ______ x10^6 mm^3 (3 decimal places) c. The plastic moment with bending about the vertical axis if Fy = 345 MPa. _______kN-m (rounded to the nearest whole number)
A wooden beam is loaded by a distributed load w = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1900 mm, L BC = 3100 mm, W=200 mm, Bo = 30 mm, and H = 200 mm, ho=20 mm. %3D Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. Steps: Fill the gaps in the "steps" to get some marks from the working-out process. Adaptive marking is still used. (a) (b) W hol Во H B LAB LBC Cross-section W Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam.
A torque wrench is used to tighten the nut on a bolt. If the dial indicates that a torque of 60 lb # ft is applied when the bolt is fully tightened, determine the force P acting at the handle and the distance s the needle moves along the scale. Assume only the portion AB of the beam distorts. The crosssection is square having dimensions of 0.5 in. by 0.5 in. E = 29(103) ksi.
For the section shown in the figure below: (a) Determine the coordinates of the centroid with respect to point “O”. (b) Find the second moment of area of the section about “x” axis (Ix).
Solve the slope and deflection for the problem using MAT. Draw the tangency 25 mm 75 mm 75 mm 15 kN Ti 25 mm 150 mm lines and label it completely including the required slope and deflection. E = 10GPA C and the cross section of the beam is B' shown in figure. 4 m 4 m Required Slope (radian) Required Deflection (mm) ĐA = AB = 0C = %3D Tangency Lines with EC M/EI Diagram
The bar composed of aluminum was sustained by the 14 mm2 cross-sectional area of the pin-connected rod CB. When the bar is vertically deflected at D, calculate the vertical deflection of the bar when distributed load is applied Given: E = 68.9 x 10^9 Pa