For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V = 9 kN, V2 = 9 kN, V3 = 200 mm, and V4 = 1100 mm. (mm) 0 Provide values at all key points shown in the given shear-force and bending-moment diagrams. (mm) C A = B = C = D= E = F= P = Q= B KN KN * KN * KN * KN kN E x kN-mm kN-mm D 0.00 Reaction force R₁ (left) = In the shear-force and bending-moment diagrams given, F +V 0.00 (mm) 6.3 kN and reaction force R2 (right) = P 11.7 kN. Q 0.00

For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V = 9 kN, V2 = 9 kN, V3 = 200 mm, and V4 = 1100 mm. (mm) 0 Provide values at all key points shown in the given shear-force and bending-moment diagrams. (mm) C A = B = C = D= E = F= P = Q= B KN KN * KN * KN * KN kN E x kN-mm kN-mm D 0.00 Reaction force R₁ (left) = In the shear-force and bending-moment diagrams given, F +V 0.00 (mm) 6.3 kN and reaction force R2 (right) = P 11.7 kN. Q 0.00

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions and the shear-force diagram are provided. M = 13 kN-m Ay = 3.46 KN Dy Units: KN = 32.54 kN M 4 m 29.5 kN-m 43.3 kN-m 25.8 kN-m O 22.9 kN-m 31.48 kN-m B Ay 4 m 15 kN C Ay 4 m Ay-15 7 kN/m D 3 m 21 Ay-15 E X
6. Q1: For the beam Shown in Figure 1 (40 Points) 8kN/m 3kN/m 8kN/m 1. Find the reaction at support B RBy, the bending moment at B, and the bending moment at C. B- A 2. Draw the shear force and bending 3m 2m 2m 3m moment diagram for the beam. Figure 1 Q2: (30 Points) For the simply supported beam with loading and cross section shown in Figure 2, determine the following: 1. The location of the centroid measured 10 kN 10 kN 100 from the top fiber in (mm). 2. The moment of inertia about the 50 centroidal x axis (mm“) 3. The maximum compressive stress in 0.6m 0.6 m 0.6 m 30 30 60 30, (MPa) 4. The maximum shear stress at the neutral axis in (MPa) All cross-section 5. The average shear stress on the section dimensions in mm (MPа) If the allowable stress in tension, compression, and shear are 4 MPa, 18 MP, and 12 MPa respectively. is this Figure 2 beam safe?
SHEAR AND MOMENT DIAGRAM PROBLEM 2 Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 6.9 ft, b = 10.4 ft, c = 5.8 ft, and w = 9.5 kips/ft. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. The roller at point D indicates that motion is restricted both up and down, and the beam will not lift off the roller. a B W b C D X
parts 4-5-6 please, thank you
Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in figure, mark the salient points in the diagram. Neglect the self-weight of the beam, where F1 =10 N, F2 =60N, F3 =30 N, F4 =1ON, a =5 m, b=2 m, c=3 m, d=5 m F4 F3 F2 F1 E A d. a
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
Use the graphical method to construct the shearforceand bending-moment diagrams for the beams shown in Figurebelow . Label all significant points on each diagram, andidentify the maximum moments along with their respective locations.Clearly differentiate straight-line and curved portions of thediagrams.
See attached
Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in figure, mark the salient points in the diagram. Neglect the self-weight of the beam, where F1 =10 N, F2 =60N, F3 =30 N, F4 =10N, a =5 m, b=2 m, c=3 m, d=5 m F4 F3 F2 F1 E A d. a
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=14.0 ft, b=3.0 ft, c= 7.0 ft, w = 9 kips/ft and M = 300 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. " " Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i W i a W M a B M B ес b kips kips с Cy с X с -X
3
For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Calculate the shear force V and bending moment M at a cross section located 0.5 m from the fixed support. Neglect the weight of the beam. (Show complete calculation and step by step process. Show free body diagram)