Two pipes A and B are connected in parallelbetween two points M and N as shown infigure. Pipe A is 80 mm diameter, 900 m longand its friction factor is 0.015. Pipe B is of 100mm diameter, 700 m long and its friction factoris 0.018. A total discharge of 0.030 m³/s isentering the parallel pipes through the divisionat M. Calculate the discharge in the two pipesA and B.M= 0.015A fA80 mm dia, 900 m100 mm dia, 700 mBfB = = 0.018N

Answered: Image /qna-images/answer/daf721db-04b0-49fa-92f1-b1de4246c77f.jpg

Answered: Two pipes A and B are connected in…

Two pipes A and B are connected in parallel between two points M and N as shown in figure. Pipe A is 80 mm diameter, 900 m long and its friction factor is 0.015. Pipe B is of 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This is a mechanics of deformable bodies problem
The planar AB cover with a width b = 2 m perpendicular to the plane of the figure is articulated at point B F = 7620 Newton force is applied from point A. Since the weight of the lid is W = 5600 N, find the water depth h for the equilibrium state.Note: Specific mass of water is ρsu = 1000 kg / m3. (figure in image) #fluidmechanics
6 The Reynold number for the flow through smooth pipe is given by 105. The value of friction factor for smooth pipe is
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
In the friction free shown, the following: compute a. Pressure of the water in the tube at point B. 1.5 m b. Pressure of water in the tube at 3 m A.
A 140 mm height of cylinder of 70 mm diameter is used as a short column and carries a pressure of -100 MPa as shown in below. Knowing that E= 105 GPa and u = 0.34,
2. In figure below fluid 1 is oil (SG=0.87) and fluid 2 is glycerin (SG=1.26) at 20°C. If P₁ = 98kPa, determine the absolute pressure at point A. Gu 10 cm P₂ Pa 32 cm Figure 2. Schematic for problem 2
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3