For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. Question 103A, the longitudinal stress is nearest to * Girth joint d Longitudinal joint Figure 103

For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. Question 103A, the longitudinal stress is nearest to * Girth joint d Longitudinal joint Figure 103

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1,80 in. and the compressive force F is 3500 lb. The maximum allowable shear stress t^^, in the wall of the cylinder is 5500 psi. What is the minimum permissible thickness t„± of the cylinder wall? (Sec figure
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
A piston-cylinder has a force F₁ applied to it. The circumferential stress in the cylinder cannot exceed Omax = 6 MPa. Hint: 1. Pressure = F Area P = F₁ F₁- OG Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value T'inner 44 mm t 1.25 mm r1 a. Determine the max pressure that the piston-cylinder can withstand, P. b. Determine the magnitude of max force that can be exerted on the piston to not exceed omax, F1. kPa N
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. Thenormal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameterof the spacer.
A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 19% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoop) stress is
TDe tuláaiceicilaal, D. ile e 200e ticioddocidcICIdCies he sim Ang 2. Fin sile wrl imd tlaeide hrety- 5. JAns. 3 mm) 3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take JAns. 6.25 mm] maximum tensile stress for cast iron as 14 MPa. fIm and is to be subiected to an internal pressure of 2.75
1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.