For fluids with small Prandt number the thermal boundary layer development is much choose your answer. than that of the velocity boundary layer (õt » õ), and it is reasonable to assume choose your answer... velocity (u = u0) throughout the thermal boundary layer

For fluids with small Prandt number the thermal boundary layer development is much choose your answer. than that of the velocity boundary layer (õt » õ), and it is reasonable to assume choose your answer... velocity (u = u0) throughout the thermal boundary layer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 7 cm diameter bed on a 25 cm long bed, as shown in the figure below. The shaft rotates at 3200 revolutions per minute with uniform intervals of 0.2 mm. Continuous operation The temperatures of the shaft and bearing adjacent to the oil gap are 55 0C. your oil viscosity 0.05 N.s/m2 and its thermal conductivity is 0.17 W/m.K. Continuity, momentum and by simplifying the energy equations and solving for each separately, a) The maximum temperature of the oil, b) Calculate the heat transfer rates to the bearing and shaft.
ricant An oil is acting as a lubricant for a pair of cylindrical surfaces such as those shown in 1. The angular velocity of the outer cylinder is 7908 rpmt. The outer cylinder has a radius of 5.06 cm, and the clearance between the cylinders is 0.027 cm. What is the maxi- mum temperature in the oil if both wall temperatures are known to be 158° F? The physical properties of the oil are viscosity density thermal conductivity 92.3 cp 1.22 g cm-3 0.0055 cal sec-1 cm-1 ° C-1
how to quickly recognize isothermal boundary condition. and in case of isothermal boundary conditions, sometimes its writtens as T=To and sometimes written dT/dx=0 which one to apply?
Prove that by using dimensional analysis Nusselt number is a function of Reynolds number and Prandtl number in forced convection
Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose temperatureis Ts,1= 40°C and thermal conductivity of steel is 671 w/m.k. The wall is 0.35 m thick, and itsother surface temperature is Ts,2= 100°C. For steadystateconditions what is the convection coefficient associatedwith the water flow?
Hot Air blows over steel plate with dimension (5000mm * 7.5m)), the steel plate temperature is 22'C, the convection heat-transfer coefficient is h= {25 W/m2- C}. Calculate the heat transfer? if you know that thermometer reader read air temperature is 492 K
Need answer ASAP! Thank you Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 10 W/(m2-K). Assume the apple can be described as a sphere with an 8 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.4 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3 a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?
HEAT TRANSFER From the heat transfer property table of water, the properties at 20 0C are as follows: Density = 997.36 kg/m3 Kinematic viscosity = 1.026 × 10-6 m2/s Prandtl number = 7.17 (i) Thickness of hydrodynamic boundary layer = 9.24 mm (ii) Thickness of thermal boundary layer = 4.79 mm (iii)Local friction coefficient = 0.001228 Average friction coefficient = 0.002456 ANSWER QUESTION (iv) ,(vi) and B
Introduction to heat convection Solved problems HW-10- 1- Determine the velocity distribution in the velocity boundary layer assuming second degree polynomial: u =C, +C,y+C3y? Answer: The boundary conditions are: du .. u = 0 at y = 0 ; u = u, ; at y = 6 ; = 0 at y = 8 dy и y y This gives: 2.
Consider a pipe of 5 m in length and 1 cm in diameter. Temperature difference between the wall and the fluid (k = 1 W/mK) at exit is 25% that of at inlet. If the pipe wall temperature remains as constant of 80 ºC, total heat transfer rate 1000 W, and the flow is laminar what is the fluid temperature at inlet?
Assume that the head can be modeled as a hemisphere (radius ro 90 mm) with a single layer of brain tissue (k-0.5 W/m °C). The bottom of the hemisphere is insulated. The head surface is assumed exposed to a convection environment (h-8 W/m²K, T-25°C). Based on the boundary conditions, the brain tissue temperature can be treated as 1-D, i.e., T.(r), where r is the radial variable in the spherical coordinates. The volumetric metabolic heat generation rate in the brain is uniformly distributed and is equal to q=10000 W/m³. Consider two situations, a) no blood perfusion is considered; b) blood perfusion rate is uniform in the brain and is equal to @=0.01 s¹. The governing equation (steady state, 1-D heat transfer in the spherical coordinate system, with or without the Pennes perfusion term) and boundary conditions for both situations can be written as: k₁ 1 d 2 r=0 dr dT, dr dT, 17/17) + 0 dr =0 T,(r)= dT, r=r-k₁- =h(T, -T.) dr (a) For the first situation without considering blood perfusion…
Example 1 Engine oil at 60°C flows over a 5 m long flat plate whose temperature is 20°C with a velocity of 2 m/s with a surface film temperature of 40°C. The density, thermal conductivity, Prandlt No. and kinematic viscosity are 876 kg/m², 0.144 W/m.K, 28270, and 242 x 10$ m²/s, respectively. Determine the total drag force and the rate of heat transfer per unit width of the entire plate. oil T- = 60°C V-=2 m/s T=20°C- L= 5 m We assume the critical Reynolds number is 5x105. The properties of the oil at the film temperature are: