An oil is acting as a lubricant for a pair of cylindrical surfaces such as those shown in The angular velocity of the outer cylinder is 7908 rpnt. The outer cylinder has a radius of 5.06 cm, and the clearance between the cylinders is 0.027 cm. What is the maxi- mum temperature in the oil if both wall temperatures are known to be 158° F? The physical properties of the oil are

An oil is acting as a lubricant for a pair of cylindrical surfaces such as those shown in The angular velocity of the outer cylinder is 7908 rpnt. The outer cylinder has a radius of 5.06 cm, and the clearance between the cylinders is 0.027 cm. What is the maxi- mum temperature in the oil if both wall temperatures are known to be 158° F? The physical properties of the oil are

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.26P

See similar textbooks

Similar questions

A rotating viscometer consists of two concentric cylinders—a stationary inner cyliner of radius Ri and an outer cylinder of inside radius Ro rotating at angular velocity (rotation rate) ?o. In the tiny gap between the two cylinders is the fluid whose viscosity (? ) is to be measured. The length of the cylinders in Fig is L. L is large such that end effects are negligible (we can treat this as a two-dimensional problem). Torque (T) is required to rotate the inner cylinder at constant speed. Showing all your work and algebra, generate an approximate expression of T as a function of the other variables.
During the experiment on the determination of surface tension of liquids by the capillary rise method, which among the following reagents is not used? * O Chloroform O Benzene O Acetone O Methanol
Viscons effect amed modified Bermoulli's ex (Gmided workonts) 2.H Problem I 2 concentic dnms form an omular Space which is filled with a fluid of niscosity 0-2 kg/s 4 the inner and owter cylinders rotate with 5rad's and 4redfs respective angilar speed, find the visloy tongue per unit axial Censth- 4nads 0-5m Fluid m-3 Stepl Decicle on the quantity to be determined fint, + select the primciple aronding ly. Step2 Think wshat next. 4 you get the ht step might, the second one is obvions. There is, howener, a chunce that you were ambushed in the finst step. So think hardo
cenical body is made to rotate d a constent visesity A A film of oil having of oro02 NS/m² seperates the cone from the container. What to rque is required to maintain this motion. The cone has a eol m tall. s peed of to rad/s a The fi lm thickness is 0:25 mm ra dius at the base and is P10 rad/s 025 film
Toluene is being stored in a 5 m diameter cylindrical tank under a pressure of 400 kPa (absolute). The tank drains through a 2 cm diameter line located 8 m below the liquid level of the tank, you can assume that the pressure at the outlet of this line is 1 atm. Toluene has a density of 870 kg m-3 and a viscosity of 0.56 mPa s. Using Bernoulli's equation (or otherwise) estimate the liquid velocity in the drain line when the valve is opened, and hence determine how long it will take for the tank drain. Comment as to whether or not you will think the tank will actually take more or less time to drain than the value you have calculated.
lied adlo ooab od Discutions :- What is the effect of Time and the relative viscosity of the liquid? bods Give reasons for the (%) error calculated.
How does the pressure vary at depth (Z) in liquid and gaseous fluids, and explain the reasons why there are differences.
Two square flat parallel plates with dimensions of is 50cm x 50cm. The oil film with thickness of 12 mm exists between the two plates, the upper plate which moves at 3 m/s requires a force of F 3t N to maintain the speed and the lower plate is stationary. Determine the dynamic viscosity of oil and the Kinematic viscosity of oil if the specific gravity of oil is 0.95.
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.72 W/m deg C, Re=3840000, and Pr=0.7)?
An oil is contained between 2 identical parallel plates of 2m2area each. The top plate is pulled tothe left (-x direction) with a force of 0.33N at a velocity of 0.3 m/s. The bottom plate is pulled in theopposite direction with a force of 0.11N at a velocity of 0.1 m/s. The plates are 5mm apart. Whatis the viscosity of the oil in cP?
Air is contained in a piston cylinder device, it expands first isothermally (1=>2) then isobaric expansion takes place (2=>3). The processes on the T-v diagram will be: Select one: A. (1-2) Horizontal line, (2-3) Inclined line with Positive slope. B. (1-2) Inclined line with Positive slope, (2-3) Horizontal line. C. (1-2) Inclined line with Negative slope, (2-3) Horizontal line. O D. (1-2) Horizontal line, (2-3) Inclined line with Negative slope. O E. (1-2) Horizontal line, (2-3) Vertical line downward. F. (1-2) Horizontal line, (2-3) Vertical line upward.
The area between two infinite flat parallel sheets which are placed 10mm awayfrom each other is occupied with a fluid having dynamic viscosity 0.5Pa.s.Through this distance between the sheets a plate with small thickness and crosssectional area 0.1m2 is being pulled. Considering the plate is at 4mm distance fromone of the sheets and the velocity distribution is linear determine the amount offorce which is needed to pull the plate.